Characterization of the Microstructure and Interfacial Morphology of Magnetic Pulse Welded Steel/Al Tubes
Materials · 08.02.2025 · 18 (4) · 757
DOI: 10.3390/ma18040757 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 08.02.2025. Verfasst von Tianhan Hu und 5 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Advanced Special Steel, School of Materials Science and Engineering, Shanghai University, Shanghai 200444, China. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China.
Abstract (Originalsprache)
Facing the global energy crisis and increasingly stringent environmental protection regulations, automotive lightweighting has become a core issue for the sustainable development of the automotive industry. In particular, the qualified combination of steel and aluminum alloy has become a promising development direction to achieve the aim of lightweight design. As an innovative solid-phase welding technique, magnetic pulse welding (MPW) exhibits unique advantages in joining these dissimilar metals. The 6061 Al alloy and 20# steel tubes were joined by the MPW technique in this study. The microstructure and interface morphology of the MPW steel/Al tube were characterized using optical microscopy (OM), scanning electron microscopy (SEM), and an electro-probe microanalyzer (EPMA). The microstructure in the region adjacent to the interface was similar to that of the base metals (BMs). The element transition zone could be observed at the interface. The thickness of the transition layer was approximately 6 μm. The transition layer did not possess high hardness and brittleness like the Fe–Al binary IMC layer. Therefore, the interface bonding quality and long-term stability of the MPW steel/Al joint were relatively good. The welded joint interface could be divided into three zones: the bonded zone in the center and unbonded zones on both sides. In particular, an obvious wavy interface with gradually increased amplitude was detected in the bonded zone. The interaction between the reflected wave and the welding collision point could promote the initiation of the wavy interface. In addition, the formation of the wavy interface depended on the impact velocity and angle of the MPW process. The qualified mechanical properties of the joint could be attributed to the formation of the wavy interface. The microhardness at the interface was higher than that on both sides, owing to work hardening, at approximately 226 HV.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- State Key Laboratory of Advanced Special Steel, School of Materials Science and Engineering, Shanghai University, Shanghai 200444, China.
- State Key Laboratory of Development and Application Technology of Automotive Steels (Baosteel Group), Shanghai 201900, China.
- Automobile Steel Research Institute, R&D Center, Baoshan Iron & Steel Co., Ltd., Shanghai 201900, China.
ORCID-Profile: Hua Pan
Förderung
- National Natural Science Foundation of China
Zitieren
APA
Hu, T., Li, B., Wu, T., Pan, H., Ding, K., & Gao, Y. (2025). Characterization of the Microstructure and Interfacial Morphology of Magnetic Pulse Welded Steel/Al Tubes. Materials, 18(4), 757. https://doi.org/10.3390/ma18040757
Vancouver
Hu T, Li B, Wu T, Pan H, Ding K, Gao Y. Characterization of the Microstructure and Interfacial Morphology of Magnetic Pulse Welded Steel/Al Tubes. Materials. 2025;18(4):757. doi:10.3390/ma18040757
BibTeX
@article{Hu2025,
author = {Hu, Tianhan and Li, Bolong and Wu, Tianhai and Pan, Hua and Ding, Kai and Gao, Yulai},
title = {Characterization of the Microstructure and Interfacial Morphology of Magnetic Pulse Welded Steel/Al Tubes},
journal = {Materials},
year = {2025},
volume = {18},
number = {4},
pages = {757},
doi = {10.3390/ma18040757}
}
EUVIMED