Microstructure and Properties of AlxCr1−xCoFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering
Materials · 08.02.2025 · 18 (4) · 755
DOI: 10.3390/ma18040755 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 08.02.2025. Verfasst von Gang Li und 7 weiteren Autor:innen. Beteiligte Einrichtung: College of Mines, Liaoning Technical University, Fuxin 123000, China. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Foundation of Liaoning Educational Committee, Liaoning Provincial Engineering Research Center for High-Value Utilization of Magnesite, Key Laboratory of Mineral High Value Conversion and Energy Storage Materials of Liaoning Province.
Abstract (Originalsprache)
CoCrFeNi high-entropy alloys represent a novel structural material with considerable application potential in a variety of fields, including aerospace, automobiles, ships, machining, energy, soft magnetic materials, and hydrogen storage materials. The present study investigates the impact of the Al element on the structure and properties of the alloy. The preparation of the AlxCr1−xCoFeNi (x = 0.1, 0.2, 0.3, 0.4, 0.5) powders involved the use of a variety of elemental metal powders as raw materials and a mechanical alloying process at 350 rpm for 40 h. The sintering of the alloy powders was subsequently conducted using spark plasma sintering at 1000 °C. The microstructure of the alloys was analyzed using XRD, SEM, and EDS, and the properties were analyzed using a universal testing machine, a hardness measurement, friction and wear measurement, and an electrochemical workstation. The study shows that when x = 0.1, the crystal structure of Al0.1Cr0.9CoFeNi consists of a double FCC phase and a trace amount of σ phase. As the aluminum content increases, part of the FCC phase begins to transform to BCC. When x = 0.2~0.5, the alloy consists of a double FCC phase and a BCC phase and a trace amount of a sigma phase. As the BCC phase in the alloy increases, the tensile strength of the alloy increases, the ability to deform plastically decreases, and the hardness increases. The highest ultimate tensile strength of 1163.14 MPa is exhibited by Al0.5Cr0.5CoFeNi, while the minimum elongation is 26.98% and the maximum hardness value is 412.6 HV. In the initial stage of friction measurement, the wear mechanism of AlxCr1−xCoFeNi is adhesive wear. However, as the test time progresses, an oxide layer begins to form on the alloy’s surface, leading to a gradual increase in the friction coefficient. At this stage, the wear mechanism becomes a combination of both adhesive and abrasive wear. Once the oxidation process and the wear process have reached a dynamic equilibrium, the friction coefficient stabilizes, and the wear mechanism transitions to a state of abrasive wear. The Al0.1Cr0.9CoFeNi alloy demonstrates the lowest friction coefficient and wear rate, exhibiting values of 0.513 and 0.020 × 10−3 mm3/Nm, respectively, while the Al0.5Cr0.5CoFeNi alloy demonstrates the highest performance, with a self-corrosion voltage of 0.202 V in a 3.5 wt.% NaCl solution. The experimental findings demonstrate that, in the presence of a decline in the Cr element within a high-entropy alloy, an augmentation in the Al element can facilitate the transition of the FCC phase to the BCC phase within the alloy, thereby enhancing its mechanical properties. However, in the AlxCr1−xCoFeNi HEAs, the presence of the Cr-rich and Cr-poor phases invariably results in selective corrosion in a neutral NaCl solution. The corrosion resistance of this alloy is weaker than that of a single-phase solid solution alloy with a similar chemical composition that only undergoes pitting corrosion.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- College of Mines, Liaoning Technical University, Fuxin 123000, China.
- School of Materials Science and Engineering, Yingkou Institute of Technology, Yingkou 115000, China.
- School of Metallurgy and Materials Engineering, Liaoning Institute of Science and Technology, Benxi 117004, China.
ORCID-Profile: Xiangran Meng
Förderung
- Foundation of Liaoning Educational Committee
- Liaoning Provincial Engineering Research Center for High-Value Utilization of Magnesite
- Key Laboratory of Mineral High Value Conversion and Energy Storage Materials of Liaoning Province
Zitieren
APA
Li, G., Meng, X., Geng, C., Wang, C., Ren, H., Guo, X., Li, S., & Tao, Y. (2025). Microstructure and Properties of AlxCr1−xCoFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering. Materials, 18(4), 755. https://doi.org/10.3390/ma18040755
Vancouver
Li G, Meng X, Geng C, Wang C, Ren H, Guo X, et al. Microstructure and Properties of AlxCr1−xCoFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering. Materials. 2025;18(4):755. doi:10.3390/ma18040755
BibTeX
@article{Li2025,
author = {Li, Gang and Meng, Xiangran and Geng, Chunpin and Wang, Chongshuo and Ren, Haifang and Guo, Xiaoying and Li, Sinan and Tao, Ying},
title = {Microstructure and Properties of AlxCr1−xCoFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering},
journal = {Materials},
year = {2025},
volume = {18},
number = {4},
pages = {755},
doi = {10.3390/ma18040755}
}
EUVIMED