EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Thermoanalytical Investigation of the Curing Kinetics of Sodium Silicate as an Inorganic Binder for 3D Sand Printing

Jakob Glück, Timon Dommaschk iD, Daniel Jüngst, Jonas Arimont, Andreas Schilling iD, Martin Fehlbier

Materials · 03.02.2025 · 18 (3) · 667

DOI: 10.3390/ma18030667 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 03.02.2025. Verfasst von Jakob Glück und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Foundry Technology, University of Kassel, Emder Straße 1, 34225 Baunatal, Germany. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Regional Development Fund, European Union—Next Generation EU.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the development and application of climate friendly processes in the foundry industry, particularly with regard to the use of inorganic binders to reduce emissions and pollution. An inorganic binder system based on water glass, which is used in 3D printing technology for the production of sand molds and core, is being tested and the possibility of determining a kinetic model for the curing kinetics of sodium silicate as an inorganic binder is investigated. The aim is to use a kinetic model to better describe the microwave process currently required in binder jetting for drying the binder and catalyzing the chemical reaction of the binder during curing. For sodium silicate in particular, there is still no scientific knowledge available in this respect, which is why basic investigations based on thermogravimetry or heat flow difference calorimetry must first be carried out. In this way, it should be possible to simulate the drying process in the microwave, which has so far been based on empirical values, in order to maximize the efficiency of this process and also the quality of the components. The results indicate that the weight loss and weight changes depend on the heating rates and that a heating rate of 30 K/min is not sufficient to fully cure the sample at 500 °C. The thermogravimetric analysis (TGA) shows that the fastest weight loss occurs at the beginning of the measurement, indicating a partial pre-curing of the sample before the measurement. From the measurements, an average activation energy of 144.18 kJ/mol could be determined using the Friedman method and 123.36 kJ/mol and 123.31 kJ/mol using the Ozawa–Flynn–Wall and Kissinger–Akahira–Sunose methods, respectively. Measurements of the heat flow at a heating rate of 30 K/min indicate partially exothermic reactions during the curing process.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingbinder jettingcastingdifferential calorimetrykinetic modelsand coresodium silicatethermoanalyticsthermogravimetry

Autor:innen und Institutionen

  • Department of Foundry Technology, University of Kassel, Emder Straße 1, 34225 Baunatal, Germany.

ORCID-Profile: Timon Dommaschk, Andreas Schilling

Förderung

  • European Regional Development Fund
  • European Union—Next Generation EU

Zitieren

APA

Glück, J., Dommaschk, T., Jüngst, D., Arimont, J., Schilling, A., & Fehlbier, M. (2025). Thermoanalytical Investigation of the Curing Kinetics of Sodium Silicate as an Inorganic Binder for 3D Sand Printing. Materials, 18(3), 667. https://doi.org/10.3390/ma18030667

Vancouver

Glück J, Dommaschk T, Jüngst D, Arimont J, Schilling A, Fehlbier M. Thermoanalytical Investigation of the Curing Kinetics of Sodium Silicate as an Inorganic Binder for 3D Sand Printing. Materials. 2025;18(3):667. doi:10.3390/ma18030667

BibTeX
@article{Glck2025,
  author = {Glück, Jakob and Dommaschk, Timon and Jüngst, Daniel and Arimont, Jonas and Schilling, Andreas and Fehlbier, Martin},
  title = {Thermoanalytical Investigation of the Curing Kinetics of Sodium Silicate as an Inorganic Binder for 3D Sand Printing},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {3},
  pages = {667},
  doi = {10.3390/ma18030667}
}
Kostenlos starten →