EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multi-Objective Optimization of Injection Molding Process Parameters for Junction Boxes Based on BP Neural Network and NSGA-II Algorithm

Tengjiao Hong, Dong Huang, Fengjuan Ding iD, Liyong Zhang, Fulong Dong, Lei Chen

Materials · 27.01.2025 · 18 (3) · 577

DOI: 10.3390/ma18030577 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.01.2025. Verfasst von Tengjiao Hong und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Intelligent Manufacturing, Anhui Science and Technology University, Chuzhou 233100, China. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Science Research Project of Higher Education Institutions in Anhui Province, Anhui Provincial Key Laboratory of Functional Agriculture and Functional Food, Anhui Science and Technology University, Talent Introduction Project of Anhui Science and Technology University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Many factors affect the quality of the injection molding of plastic products, including the process parameters, mold materials, type and geometry of plastic parts, cooling system, pouring system, etc. A multi-objective optimization method for injection molding process parameters based on the BP neural network and NSGA-II algorithm is proposed to address the problem of product quality defects caused by unreasonable process parameter settings. Taking the junction box shell as the object, numerical simulation was carried out using Moldflow2019 software and a six-factor five-level orthogonal experiment was designed to explore the influence of injection molding process parameters, such as the mold temperature, melt temperature, injection pressure, holding pressure, holding time, and cooling time, on the volume shrinkage rate and warpage deformation of the junction box. Based on a numerical simulation, the BP neural network and NSGA-II algorithm were used to optimize the optimal combination of injection molding process parameters, volume shrinkage rate, and warpage deformation. The research results indicate that the melt temperature has the most significant impact on the quality of the injection molding of junction boxes, followed by the holding time, holding pressure, cooling time, injection pressure, and mold temperature. After optimization using the BP neural network and the NSGA-II algorithm, the optimal process parameter combination was obtained with a melt temperature of 230.03 °C, a mold temperature of 51.27 °C, an injection pressure of 49.13 MPa, a holding pressure of 69.01 MPa, a holding time of 15.48 s, and a cooling time of 34.91 s. At this time, the volume shrinkage rate and warpage deformation of the junction box were 6.905% and 0.991 mm, respectively, which decreased by 33.2% and 3.8% compared to the average volume shrinkage rate (10.34884%) and warpage deformation (1.030764 mm) before optimization. The optimization effect was significant. In addition, the errors between the volume shrinkage rate and warpage deformation predicted by BP-NSGA-II and the simulated values using Moldflow software were 1.9% and 3.4%, respectively, indicating that the optimization method based on the BP neural network model and NSGA-II algorithm is reliable.

Schlagwörter

Stichwörter der Autor:innen

BP neural networkjunction boxmulti-objective optimizationprocess parametersvolume shrinkage ratewarping deformation

Autor:innen und Institutionen

  • College of Intelligent Manufacturing, Anhui Science and Technology University, Chuzhou 233100, China.
  • School of Business Administration, Stamford International University, Bangkok 10250, Thailand.
  • Fengyang County Science and Technology Innovation Service Center, Chuzhou 233100, China.

ORCID-Profile: Fengjuan Ding

Förderung

  • Natural Science Research Project of Higher Education Institutions in Anhui Province
  • Anhui Provincial Key Laboratory of Functional Agriculture and Functional Food, Anhui Science and Technology University
  • Talent Introduction Project of Anhui Science and Technology University
  • Design and Key Technology Research of Multi parameter Intelligent Control Instrument Junction Box
  • Research and Development of Fermentation Feed Drying Automatic Line
  • Key technologies and applications of impinging stream based plant protection hedge spray system

Zitieren

APA

Hong, T., Huang, D., Ding, F., Zhang, L., Dong, F., & Chen, L. (2025). Multi-Objective Optimization of Injection Molding Process Parameters for Junction Boxes Based on BP Neural Network and NSGA-II Algorithm. Materials, 18(3), 577. https://doi.org/10.3390/ma18030577

Vancouver

Hong T, Huang D, Ding F, Zhang L, Dong F, Chen L. Multi-Objective Optimization of Injection Molding Process Parameters for Junction Boxes Based on BP Neural Network and NSGA-II Algorithm. Materials. 2025;18(3):577. doi:10.3390/ma18030577

BibTeX
@article{Hong2025,
  author = {Hong, Tengjiao and Huang, Dong and Ding, Fengjuan and Zhang, Liyong and Dong, Fulong and Chen, Lei},
  title = {Multi-Objective Optimization of Injection Molding Process Parameters for Junction Boxes Based on BP Neural Network and NSGA-II Algorithm},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {3},
  pages = {577},
  doi = {10.3390/ma18030577}
}
Kostenlos starten →