EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Deformation Behavior of Inconel 625 Alloy with TPMS Structure

Kangning Xu iD, Jiahui Cao, Zhiwei Zheng, Rusheng Zhao, Gaopeng Xu, Hao Wang iD, Jincheng Wang iD, Boyoung Hur, Xuezheng Yue

Materials · 16.01.2025 · 18 (2) · 396

DOI: 10.3390/ma18020396 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 16.01.2025. Verfasst von Kangning Xu und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Materials and Chemistry, University of Shanghai for Science and Technology, Shanghai 200082, China. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Shanghai Engineering Research Center of High-Performance Medical Device Materials.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Triply periodic minimal surfaces (TPMSs) are known for their smooth, fully interconnected, and naturally porous characteristics, offering a superior alternative to traditional porous structures. These structures often suffer from stress concentration and a lack of adjustability. Using laser powder bed fusion (LPBF), we have fabricated Inconel 625 sheet-based TPMS lattice structures with four distinct topologies: Primitive, IWP, Diamond, and Gyroid. The compressive responses and energy absorption capabilities of the four lattice designs were meticulously evaluated. The discrepancies between theoretical predictions and the fabricated specimens were precisely quantified using the Archimedes’ principle for volume displacement. Subsequently, the LPBF-manufactured samples underwent uniaxial compression tests, which were complemented by numerical simulation for validation. The experimental results demonstrate that the IWP lattice consistently outperformed the other three configurations in terms of yield strength. Furthermore, when comparing energy absorption efficiencies, the IWP structures were confirmed to be more effective and closer to the ideal performance. An analysis of the deformation mechanisms shows that the IWP structure characteristically failed in a layer-by-layer manner, distinct from the other structures that exhibited significant shear banding. This distinct behavior was responsible for the higher yield strength (113.16 MPa), elastic modulus (735.76 MPa), and energy absorption capacity (9009.39 MJ/m3) observed in the IWP configuration. To examine the influence of porosity on structural performance, specimens with two varying porosities (70% and 80%) were selected for each of the four designs. Ultimately, the mechanical performance of Inconel 625 under compression was assessed both pre- and post-deformation to elucidate its impact on the material’s integrity.

Schlagwörter

Stichwörter der Autor:innen

Inconel 625compressive propertyenergy absorption characteristiclaser powder bed fusiontriply periodic minimal surface

Autor:innen und Institutionen

  • School of Materials and Chemistry, University of Shanghai for Science and Technology, Shanghai 200082, China.
  • Department of Aerospace Engineering, Tokyo Metropolitan University, Tokyo 191-0065, Japan.
  • Department of Mechanical Engineering, The University of Melbourne, Parkville, VIC 3010, Australia.
  • School of Engineering, M050, The University of Western Australia, 35 Stirling Highway, Crawley, Perth, WA 6009, Australia.
  • Department of Metallurgical and Materials Engineering, Gyeongsang National University, Jinju-si 501, Republic of Korea.

ORCID-Profile: Kangning Xu, Hao Wang, Jincheng Wang

Förderung

  • National Natural Science Foundation of China
  • Shanghai Engineering Research Center of High-Performance Medical Device Materials

Zitieren

APA

Xu, K., Cao, J., Zheng, Z., Zhao, R., Xu, G., Wang, H., Wang, J., Hur, B., & Yue, X. (2025). Deformation Behavior of Inconel 625 Alloy with TPMS Structure. Materials, 18(2), 396. https://doi.org/10.3390/ma18020396

Vancouver

Xu K, Cao J, Zheng Z, Zhao R, Xu G, Wang H, et al. Deformation Behavior of Inconel 625 Alloy with TPMS Structure. Materials. 2025;18(2):396. doi:10.3390/ma18020396

BibTeX
@article{Xu2025,
  author = {Xu, Kangning and Cao, Jiahui and Zheng, Zhiwei and Zhao, Rusheng and Xu, Gaopeng and Wang, Hao and Wang, Jincheng and Hur, Boyoung and Yue, Xuezheng},
  title = {Deformation Behavior of Inconel 625 Alloy with TPMS Structure},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {2},
  pages = {396},
  doi = {10.3390/ma18020396}
}
Kostenlos starten →