EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Use of 3D Printing Filaments to Build Moisture Sensors in Porous Materials

Magdalena Paśnikowska-Łukaszuk iD, Joanna Szulżyk-Cieplak iD, Magda Wlazło, Jarosław Zubrzycki iD, Ewa Łazuka iD, Arkadiusz Urzędowski iD, Zbigniew Suchorab iD

Materials · 30.12.2024 · 18 (1) · 115

DOI: 10.3390/ma18010115 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 30.12.2024. Verfasst von Magdalena Paśnikowska-Łukaszuk und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mathematics and Information Technology, Lublin University of Technology, Nadbystrzycka 38, 20-618 Lublin, Poland. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 60 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Lublin University of Technology, Ministry of Science and Higher Education in Poland, LUT university program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study explores the application of materials used in 3D printing to manufacture the housings of non-invasive sensors employed in measurements using a TDR (Time Domain Reflectometry) meter. The research investigates whether sensors designed with 3D printing technology can serve as viable alternatives to conventional invasive and non-invasive sensors. This study focuses on innovative approaches to designing humidity sensors, utilizing Fused Deposition Modeling (FDM) technology to create housings for non-invasive sensors compatible with TDR devices. The paper discusses the use of 3D modeling technology in sensor design, with particular emphasis on materials used in 3D printing, notably polylactic acid (PLA). Environmental factors, such as moisture in building materials, are characterized, and the need for dedicated sensor designs is highlighted. The software utilized in the 3D modeling and printing processes is also described. The Materials and Methods Section provides a detailed account of the construction process for the non-invasive sensor housing and the preparation for moisture measurement in silicate materials using the designed sensor. A prototype sensor was successfully fabricated through 3D printing. Using the designed sensor, measurements were conducted on silicate samples soaked in aqueous solutions with water absorption levels ranging from 0% to 10%. Experimental validation involved testing silicate samples with the prototype sensor to evaluate its effectiveness. The electrical permittivity of the material was calculated, and the root-mean-square error (RMSE) was determined using classical computational methods and machine learning techniques. The RMSE obtained using the classical method was 0.70. The results obtained were further analyzed using machine learning models, including Gaussian Process Regression (GPR) and Support Vector Machine (SVM). The GPR model achieved an RMSE of 0.15, while the SVM model yielded an RMSE of 0.25. These findings confirm the sensor’s effectiveness and its potential for further research and practical applications.

Schlagwörter

Stichwörter der Autor:innen

3D printingPLATDRbuilding materialsmeasurement methodsmoisture transport

Autor:innen und Institutionen

  • Faculty of Mathematics and Information Technology, Lublin University of Technology, Nadbystrzycka 38, 20-618 Lublin, Poland.
  • Faculty of Environmental Engineering, Lublin University of Technology, Nadbystrzycka 40B, 20-618 Lublin, Poland.

ORCID-Profile: Magdalena Paśnikowska-Łukaszuk, Joanna Szulżyk-Cieplak, Jarosław Zubrzycki, Ewa Łazuka, Arkadiusz Urzędowski, Zbigniew Suchorab

Förderung

  • Lublin University of Technology
  • Ministry of Science and Higher Education in Poland
  • LUT university program

Zitieren

APA

Paśnikowska-Łukaszuk, M., Szulżyk-Cieplak, J., Wlazło, M., Zubrzycki, J., Łazuka, E., Urzędowski, A., & Suchorab, Z. (2024). The Use of 3D Printing Filaments to Build Moisture Sensors in Porous Materials. Materials, 18(1), 115. https://doi.org/10.3390/ma18010115

Vancouver

Paśnikowska-Łukaszuk M, Szulżyk-Cieplak J, Wlazło M, Zubrzycki J, Łazuka E, Urzędowski A, et al. The Use of 3D Printing Filaments to Build Moisture Sensors in Porous Materials. Materials. 2024;18(1):115. doi:10.3390/ma18010115

BibTeX
@article{Panikowskaukaszuk2024,
  author = {Paśnikowska-Łukaszuk, Magdalena and Szulżyk-Cieplak, Joanna and Wlazło, Magda and Zubrzycki, Jarosław and Łazuka, Ewa and Urzędowski, Arkadiusz and Suchorab, Zbigniew},
  title = {The Use of 3D Printing Filaments to Build Moisture Sensors in Porous Materials},
  journal = {Materials},
  year = {2024},
  volume = {18},
  number = {1},
  pages = {115},
  doi = {10.3390/ma18010115}
}
Kostenlos starten →