EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Analysis of Tool Wear in Finish Turning of Titanium Alloy Ti-6Al-4V Under Minimum Quantity Lubrication Conditions Observed with Recurrence Quantification Analysis

Joanna Lisowicz iD, Krzysztof Krupa, Kamil Leksycki iD, Rafał Rusinek iD, Szymon Wojciechowski iD

Materials · 27.12.2024 · 18 (1) · 79

DOI: 10.3390/ma18010079 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.12.2024. Verfasst von Joanna Lisowicz und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Manufacturing Techniques and Automation, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Al. Po…. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: "VIA CARPATIA Universities of Technology Network named after the President of the Republic of Poland Lech Kaczyński", under the special purpose grant from the…, “VIA CARPATIA Universities of Technology Network named after the President of the Republic of Poland Lech Kaczyński”, under the special purpose grant from the….

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Titanium alloys, particularly Ti-6Al-4V, are widely used in many industries due to their high strength, low density, and corrosion resistance. However, machining these materials is challenging due to high strength at elevated temperatures, low thermal conductivity, and high chemical reactivity. This study investigates Recurrence Plot (RP) and Recurrence Quantification Analysis (RQA) to analyze tool wear during the finish turning of Ti-6Al-4V. The tests were conducted under Minimum Quantity Lubrication (MQL). Three inserts (two coated, one uncoated) were tested, and tool life was evaluated based on material removal volume. The issue of tool exploitation and process reliability is crucial, as it directly impacts machining performance. Results show that the uncoated insert outperformed the coated ones. RQA parameters indicated a stable-to-unstable transition in coated inserts but not in the uncoated insert. This suggests that recurrence analysis can monitor cutting dynamics in coated insert machining, but further research is needed for uncoated tools. This paper’s novelty lies in applying RP and RQA to diagnose tool wear in titanium alloy machining under MQL conditions, a method not previously explored in this context.

Schlagwörter

Stichwörter der Autor:innen

minimum quantity lubricationrecurrence plotsrecurrence quantification analysistitanium alloyturning

Autor:innen und Institutionen

  • Department of Manufacturing Techniques and Automation, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Al. Powstancow Warszawy Street, 35-959 Rzeszow, Poland.
  • Department of Material Science, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Al. Powstancow Warszawy Street, 35-959 Rzeszow, Poland.
  • Institute of Mechanical Engineering, University of Zielona Gora, 4 Prof. Z. Szafrana Street, 65-516 Zielona Gora, Poland.
  • Department of Applied Mechanics, Lublin University of Technology, Nadbystrzycka 36 Street, 20-618 Lublin, Poland.
  • Institute of Mechanical Technology, Poznan University of Technology, 3 Piotrowo Street, 60-965 Poznan, Poland.
  • Department of Automobile and Manufacturing Technologies, Faculty of Manufacturing Technologies with a Seat in Presov, Technical University of Kosice, 31 Sturova Street, 080 01 Presov, Slovakia.

ORCID-Profile: Joanna Lisowicz, Kamil Leksycki, Rafał Rusinek, Szymon Wojciechowski

Förderung

  • "VIA CARPATIA Universities of Technology Network named after the President of the Republic of Poland Lech Kaczyński", under the special purpose grant from the…
  • “VIA CARPATIA Universities of Technology Network named after the President of the Republic of Poland Lech Kaczyński”, under the special purpose grant from the…

Zitieren

APA

Lisowicz, J., Krupa, K., Leksycki, K., Rusinek, R., & Wojciechowski, S. (2024). Analysis of Tool Wear in Finish Turning of Titanium Alloy Ti-6Al-4V Under Minimum Quantity Lubrication Conditions Observed with Recurrence Quantification Analysis. Materials, 18(1), 79. https://doi.org/10.3390/ma18010079

Vancouver

Lisowicz J, Krupa K, Leksycki K, Rusinek R, Wojciechowski S. Analysis of Tool Wear in Finish Turning of Titanium Alloy Ti-6Al-4V Under Minimum Quantity Lubrication Conditions Observed with Recurrence Quantification Analysis. Materials. 2024;18(1):79. doi:10.3390/ma18010079

BibTeX
@article{Lisowicz2024,
  author = {Lisowicz, Joanna and Krupa, Krzysztof and Leksycki, Kamil and Rusinek, Rafał and Wojciechowski, Szymon},
  title = {Analysis of Tool Wear in Finish Turning of Titanium Alloy Ti-6Al-4V Under Minimum Quantity Lubrication Conditions Observed with Recurrence Quantification Analysis},
  journal = {Materials},
  year = {2024},
  volume = {18},
  number = {1},
  pages = {79},
  doi = {10.3390/ma18010079}
}
Kostenlos starten →