EUVIMEDEUVIMED entdecken
ÜbersichtsarbeitOpen Access · CC BY 4.0

A Review of Additive Manufacturing of Biodegradable Fe and Zn Alloys for Medical Implants Using Laser Powder Bed Fusion (LPBF)

Irene Limón iD, Javier Bedmar iD, Juan Pablo Fernández-Hernán, Marta Multigner iD, Belén Torres iD, Joaquín Rams iD, Sandra C Cifuentes iD

Materials · 19.12.2024 · 17 (24) · 6220

DOI: 10.3390/ma17246220 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift Materials, online erschienen am 19.12.2024. Verfasst von Irene Limón und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Applied Mathematics, Materials Science and Engineering and Electronic Technology, Escuela Superior de Ciencias Experimentales y Tecnolo…. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 94 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Agencia Estatal de Investigación, Ministry of Science and Innovation of Spain (MICINN).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This review explores the advancements in additive manufacturing (AM) of biodegradable iron (Fe) and zinc (Zn) alloys, focusing on their potential for medical implants, particularly in vascular and bone applications. Fe alloys are noted for their superior mechanical properties and biocompatibility but exhibit a slow corrosion rate, limiting their biodegradability. Strategies such as alloying with manganese (Mn) and optimizing microstructure via laser powder bed fusion (LPBF) have been employed to increase Fe’s corrosion rate and mechanical performance. Zn alloys, characterized by moderate biodegradation rates and biocompatible corrosion products, address the limitations of Fe, though their mechanical properties require improvement through alloying and microstructural refinement. LPBF has enabled the fabrication of dense and porous structures for both materials, with energy density optimization playing a critical role in achieving defect-free parts. Fe alloys exhibit higher strength and hardness, while Zn alloys offer better corrosion control and biocompatibility. In vitro and in vivo studies demonstrate promising outcomes for both materials, with Fe alloys excelling in load-bearing applications and Zn alloys in controlled degradation and vascular applications. Despite these advancements, challenges such as localized corrosion, cytotoxicity, and long-term performance require further investigation to fully harness the potential of AM-fabricated Fe and Zn biodegradable implants.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturing (AM)biodegradable metalsbioresorbable implantsiron alloys (Fe)laser powder bed fusion (LPBF)zinc alloys (Zn)

Autor:innen und Institutionen

  • Department of Applied Mathematics, Materials Science and Engineering and Electronic Technology, Escuela Superior de Ciencias Experimentales y Tecnología (ESCET), Universidad Rey Juan Carlos, C/Tulipán s/n, 28933 Móstole…
  • Institute of Research on Technologies for Sustainability (ITPS), Universidad Rey Juan Carlos, C/Tulipán s/n, 28933 Móstoles, Spain.

ORCID-Profile: Irene Limón, Javier Bedmar, Marta Multigner, Belén Torres, Joaquín Rams, Sandra C Cifuentes

Förderung

  • Agencia Estatal de Investigación
  • Ministry of Science and Innovation of Spain (MICINN)

Zitieren

APA

Limón, I., Bedmar, J., Fernández-Hernán, J. P., Multigner, M., Torres, B., Rams, J., & Cifuentes, S. C. (2024). A Review of Additive Manufacturing of Biodegradable Fe and Zn Alloys for Medical Implants Using Laser Powder Bed Fusion (LPBF). Materials, 17(24), 6220. https://doi.org/10.3390/ma17246220

Vancouver

Limón I, Bedmar J, Fernández-Hernán JP, Multigner M, Torres B, Rams J, et al. A Review of Additive Manufacturing of Biodegradable Fe and Zn Alloys for Medical Implants Using Laser Powder Bed Fusion (LPBF). Materials. 2024;17(24):6220. doi:10.3390/ma17246220

BibTeX
@article{Limn2024,
  author = {Limón, Irene and Bedmar, Javier and Fernández-Hernán, Juan Pablo and Multigner, Marta and Torres, Belén and Rams, Joaquín and Cifuentes, Sandra C},
  title = {A Review of Additive Manufacturing of Biodegradable Fe and Zn Alloys for Medical Implants Using Laser Powder Bed Fusion (LPBF)},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {24},
  pages = {6220},
  doi = {10.3390/ma17246220}
}
Kostenlos starten →