Powder Metallurgy Processing to Enhance Superelasticity and Shape Memory in Polycrystalline Cu–Al–Ni Alloys: Reference Material for Additive Manufacturing
Materials · 17.12.2024 · 17 (24) · 6165
DOI: 10.3390/ma17246165 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 17.12.2024. Verfasst von Mikel Pérez-Cerrato und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Physics, Faculty of Science & Technology, University of the Basque Country, UPV/EHU, Apdo. 644, 48080 Bilbao, Spain. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 128 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Basque Government, Industry Department, Spanish Ministry of Science and Innovation, University of the Basque Country, UPV/EHU.
Abstract (Originalsprache)
Shape memory alloys (SMAs) are functional materials with a wide range of applications, from the aerospace sector to the biomedical field. Nowadays, there is a worldwide interest in developing SMAs through powder metallurgy like additive manufacturing (AM), which allows innovative building processes. However, producing SMAs using AM techniques is particularly challenging because of the microstructure required to obtain optimal functional properties. This aspect is critical in the case of Cu–Al–based SMAs, due to their high elastic anisotropy, making them brittle in polycrystalline form. In this work, we approached the processing of a Cu–Al–Ni SMA following a specific powder metallurgy route: gas atomization of a pre-alloyed melt; compaction of the atomized powders through hot isostatic pressing; and a final hot rolling plus thermal treatments. Then, the microstructure of the material was characterized by electron microscopy showing a specific [001] texture in the rolling direction that improved the functional behavior. The successive processing steps produce an increase of about 40 °C in the martensitic transformation temperatures, which can be well controlled and reproduced through the developed methodology. The thermomechanical functional properties of superelasticity and shape memory were evaluated on the final SMA. Outstanding, fully recoverable superelastic behavior of 4.5% in tension, as well as a ±5% full shape memory recovery in bending, were reported for many cycles. These experiments demonstrate the enhanced mechanical and functional properties obtained in polycrystalline Cu–Al–Ni SMAs by powder metallurgy. The present results pave the road for producing this kind of SMA with the new AM technologies, which always produce polycrystalline components and can improve their processes taking the powder metallurgy SMA, here produced, as reference material.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Physics, Faculty of Science & Technology, University of the Basque Country, UPV/EHU, Apdo. 644, 48080 Bilbao, Spain.
- CEIT-Basque Research & Technology Alliance, BRTA, Manuel Lardizabal 15, 20018 Donostia/San Sebastián, Spain.
- Tecnun, Universidad de Navarra, Manuel Lardizabal 13, 20018 Donostia/San Sebastián, Spain.
- Department of Physical Metallurgy, Centro Nacional de Investigaciones Metalúrgicas (CENIM-CSIC), Avda. Gregorio del Amo 8, 28040 Madrid, Spain.
- Aeronautics Advanced Manufacturing Centre, CFAA, University of the Basque Country, UPV/EHU, 48170 Zamudio, Spain.
ORCID-Profile: Jose F Gómez-Cortés, Ernesto Urionabarrenetxea, Fernando Carreño, María L Nó, Nerea Burgos, Jose M San Juan
Förderung
- Basque Government, Industry Department
- Spanish Ministry of Science and Innovation
- University of the Basque Country, UPV/EHU
- Basque Government, Education Department
- Industry Department of the Basque Government
- University of the Basque Country UPV/EHU
- Education Department of the Basque Country
- UPV/EHU
Zitieren
APA
Pérez-Cerrato, M., Gómez-Cortés, J. F., Urionabarrenetxea, E., Ruiz-Larrea, I., Carreño, F., Ayesta, Í., Nó, M. L., Burgos, N., & San Juan, J. M. (2024). Powder Metallurgy Processing to Enhance Superelasticity and Shape Memory in Polycrystalline Cu–Al–Ni Alloys: Reference Material for Additive Manufacturing. Materials, 17(24), 6165. https://doi.org/10.3390/ma17246165
Vancouver
Pérez-Cerrato M, Gómez-Cortés JF, Urionabarrenetxea E, Ruiz-Larrea I, Carreño F, Ayesta Í, et al. Powder Metallurgy Processing to Enhance Superelasticity and Shape Memory in Polycrystalline Cu–Al–Ni Alloys: Reference Material for Additive Manufacturing. Materials. 2024;17(24):6165. doi:10.3390/ma17246165
BibTeX
@article{PrezCerrato2024,
author = {Pérez-Cerrato, Mikel and Gómez-Cortés, Jose F and Urionabarrenetxea, Ernesto and Ruiz-Larrea, Isabel and Carreño, Fernando and Ayesta, Ízaro and Nó, María L and Burgos, Nerea and San Juan, Jose M},
title = {Powder Metallurgy Processing to Enhance Superelasticity and Shape Memory in Polycrystalline Cu–Al–Ni Alloys: Reference Material for Additive Manufacturing},
journal = {Materials},
year = {2024},
volume = {17},
number = {24},
pages = {6165},
doi = {10.3390/ma17246165}
}
EUVIMED