EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Hybrid Microwave/Solar Energy Harvesting System Using 3D-Printed Metasurfaces

Argyri Drymiskianaki iD, Zacharias Viskadourakis iD, George Kenanakis iD

Materials · 05.12.2024 · 17 (23) · 5969

DOI: 10.3390/ma17235969 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 05.12.2024. Verfasst von Argyri Drymiskianaki und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Technology, University of Crete, GR-70013 Crete, Greece. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 89 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: 2nd Call for H.F.R.I. Research Projects to Support Faculty Members & Researchers funded by the Operational Programme 'Competitiveness, Entrepreneurship and Inn…, NSRF.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, a hybrid energy harvesting system based on a conventional solar cell combined with 3D-printed metasurface units is studied. Millimeter-scale metasurface units were fabricated via the stereolithography technique, and then they were covered with conductive silver paint, in order to achieve high electric conductivity. The performance of single, as well as two-unit metasurface harvesters, was thoroughly investigated. It was found that both of them produced voltage, which peaks at their resonance frequency, demonstrating efficient energy harvesting behavior in the microwave regime. Then, the metasurface units were connected with a commercially available photovoltaic panel and the performance of the hybrid system was examined under different environmental conditions, modifying the light intensity (i.e., light, dark and shadow). It was shown that the proposed hybrid harvesting system produces a sizable voltage output, which persists, even in the case when one of the components does not contribute. Furthermore, the performance of the hybrid harvester is found to be adequate enough, although optimization of the harvesting circuit is required in order to achieve high efficiency levels. All in all, the presented experimental evidence clearly indicates the realization of a rather promising hybrid energy harvesting system, exploiting two distinct ambient energy sources, namely light and microwaves.

Schlagwörter

Stichwörter der Autor:innen

3D-printingbroadband energy harvestingmetamaterialsmicrowave energy harvestingsolar energystereolithography

Autor:innen und Institutionen

  • Department of Materials Science and Technology, University of Crete, GR-70013 Crete, Greece.
  • Institute of Electronic Structure and Laser (IESL), Foundation for Research and Technology-Hellas (FORTH), GR-70013 Crete, Greece.

ORCID-Profile: Argyri Drymiskianaki, Zacharias Viskadourakis, George Kenanakis

Förderung

  • 2nd Call for H.F.R.I. Research Projects to Support Faculty Members & Researchers funded by the Operational Programme 'Competitiveness, Entrepreneurship and Inn…
  • NSRF

Zitieren

APA

Drymiskianaki, A., Viskadourakis, Z., & Kenanakis, G. (2024). Hybrid Microwave/Solar Energy Harvesting System Using 3D-Printed Metasurfaces. Materials, 17(23), 5969. https://doi.org/10.3390/ma17235969

Vancouver

Drymiskianaki A, Viskadourakis Z, Kenanakis G. Hybrid Microwave/Solar Energy Harvesting System Using 3D-Printed Metasurfaces. Materials. 2024;17(23):5969. doi:10.3390/ma17235969

BibTeX
@article{Drymiskianaki2024,
  author = {Drymiskianaki, Argyri and Viskadourakis, Zacharias and Kenanakis, George},
  title = {Hybrid Microwave/Solar Energy Harvesting System Using 3D-Printed Metasurfaces},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {23},
  pages = {5969},
  doi = {10.3390/ma17235969}
}
Kostenlos starten →