EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Investigation of the Influence of Fused Deposition Modeling 3D Printing Process Parameters on Tensile Properties of Polylactic Acid Parts Using the Taguchi Method

Getu Koro Megersa, Wojciech Sitek iD, Agnieszka J Nowak iD, Neven Tomašić iD

Materials · 05.12.2024 · 17 (23) · 5951

DOI: 10.3390/ma17235951 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 05.12.2024. Verfasst von Getu Koro Megersa und 3 weiteren Autor:innen. Beteiligte Einrichtung: Scientific and Didactic Laboratory of Nanotechnology and Materials Technologies, Silesian University of Technology, 44-100 Gliwice, Poland. Die Arbeit wurde bisher 27-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Despite Fused Deposition Modeling (FDM) being an economical 3D printing method known for its material versatility and ease of use, the mechanical performance of FDM-produced components is significantly influenced by process parameter settings. This study investigated the effects of the layer thickness, raster angle, build orientation, and extrusion temperature on the ultimate tensile strength (UTS) and elastic modulus of Polylactic Acid (PLA) specimens using Taguchi methods, with significance analyzed through analysis of variance (ANOVA). The results indicated that the build orientation is the primary factor affecting both the UTS and elastic modulus, with a flat orientation yielding the best performance. ANOVA showed that the build orientation, raster angle, and extrusion temperature significantly influence the UTS, with the build orientation contributing 98.16%. For the elastic modulus, the build orientation and raster angle were significant, contributing 94.83% and 1.76%, respectively. The optimal parameters were a 0.16 mm layer thickness, flat build orientation, 30°/−60° raster angle, and 200 °C extrusion temperature, resulting in predicted UTS and elastic modulus values with error percentages of 4.33% and 2.74%, respectively, compared to experimental values. The regression model demonstrated high predictive accuracy, with R-squared values of 99.71% for the UTS and 99.52% for the elastic modulus.

Schlagwörter

Stichwörter der Autor:innen

Fused Deposition ModelingPolylactic AcidTaguchi methodtensile properties

Autor:innen und Institutionen

  • Scientific and Didactic Laboratory of Nanotechnology and Materials Technologies, Silesian University of Technology, 44-100 Gliwice, Poland.
  • Department of Materials Science and Engineering, Faculty of Engineering, University of Rijeka, Vukovarska 58, 51000 Rijeka, Croatia.

ORCID-Profile: Wojciech Sitek, Agnieszka J Nowak, Neven Tomašić

Zitieren

APA

Megersa, G. K., Sitek, W., Nowak, A. J., & Tomašić, N. (2024). Investigation of the Influence of Fused Deposition Modeling 3D Printing Process Parameters on Tensile Properties of Polylactic Acid Parts Using the Taguchi Method. Materials, 17(23), 5951. https://doi.org/10.3390/ma17235951

Vancouver

Megersa GK, Sitek W, Nowak AJ, Tomašić N. Investigation of the Influence of Fused Deposition Modeling 3D Printing Process Parameters on Tensile Properties of Polylactic Acid Parts Using the Taguchi Method. Materials. 2024;17(23):5951. doi:10.3390/ma17235951

BibTeX
@article{Megersa2024,
  author = {Megersa, Getu Koro and Sitek, Wojciech and Nowak, Agnieszka J and Tomašić, Neven},
  title = {Investigation of the Influence of Fused Deposition Modeling 3D Printing Process Parameters on Tensile Properties of Polylactic Acid Parts Using the Taguchi Method},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {23},
  pages = {5951},
  doi = {10.3390/ma17235951}
}
Kostenlos starten →