EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

Qing Qin, Lin Han, Gang Xiong iD, Zihan Guo, Junwei Huang, Yujuan Zhang iD, Zhen Shen iD, Changchun Ge

Materials · 27.11.2024 · 17 (23) · 5830

DOI: 10.3390/ma17235830 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.11.2024. Verfasst von Qing Qin und 7 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Powder Metallurgy and Advanced Ceramics, School of Materials Science and Engineering, University of Science and Technology Beijing, Beij…. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Digital light processing (DLP) 3D-printed Si₃N₄ ceramics, known for their exceptional performance, offer distinct advantages in meeting the high-strength and complex structural demands of industries such as aerospace, semiconductors, healthcare, automotive, energy, and machinery. However, due to Si₃N₄’s strong chemical stability, low diffusion rate, low self-sintering ability, and high melting point, achieving densification under conventional sintering conditions is challenging. As a result, sintering additives are essential to promote the sintering process, lower the sintering temperature, improve densification, and enhance performance. In this study, 45 vol% Si₃N₄ slurries were prepared using DLP 3D printing technology, incorporating nine different combinations of sintering additives, including aluminum oxide (Al2O3), yttrium oxide (Y2O3), and aluminum nitride (AlN), in various ratios with Si3N4. The slurries were then sintered at 1800 °C for 2 h under a 1 MPa N2 atmosphere. Additionally, the phase composition, microstructure, grain distribution, and crack propagation of the materials. The results showed that a Si3N4 to Al2O3 and Y2O3 ratio of 95:2.5:2.5 produced elongated β-Si3N4 grain structures and enhanced density, achieving a maximum Vickers hardness of 12.88 ± 0.52 GPa. Additionally, the synergistic toughening effect of the rod-like β-Si3N4 grains and sintering aids significantly improved the fracture toughness of the Si3N4 ceramic matrix, with a flexural strength of 540.63 ± 10.05 MPa and a fracture toughness of 4.92 ± 0.07 MPa·m1/2. This study lays the foundation for the future application of 3D-printed Si3N4 ceramics, optimization of sintering aid combinations at different ratios, and performance enhancement in extreme environments.

Schlagwörter

Stichwörter der Autor:innen

DLP 3D printingmechanical propertypressure sinteringsintering aids

Autor:innen und Institutionen

  • Institute of Powder Metallurgy and Advanced Ceramics, School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China.
  • State Key Laboratory of Multimodal Artificial Intelligence Systems, Beijing Engineering Research Center of Intelligent Systems and Technology, Institute of Automation, Chinese Academy of Sciences, Beijing 100190, China.

ORCID-Profile: Gang Xiong, Yujuan Zhang, Zhen Shen

Förderung

  • the National Natural Science Foundation of China

Zitieren

APA

Qin, Q., Han, L., Xiong, G., Guo, Z., Huang, J., Zhang, Y., Shen, Z., & Ge, C. (2024). Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics. Materials, 17(23), 5830. https://doi.org/10.3390/ma17235830

Vancouver

Qin Q, Han L, Xiong G, Guo Z, Huang J, Zhang Y, et al. Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics. Materials. 2024;17(23):5830. doi:10.3390/ma17235830

BibTeX
@article{Qin2024,
  author = {Qin, Qing and Han, Lin and Xiong, Gang and Guo, Zihan and Huang, Junwei and Zhang, Yujuan and Shen, Zhen and Ge, Changchun},
  title = {Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {23},
  pages = {5830},
  doi = {10.3390/ma17235830}
}
Kostenlos starten →