Shear Strengthening of RC Beams Using Prestressed Near-Surface Mounted Bars Reducing the Probability of Construction Failure Risk
Materials · 21.11.2024 · 17 (23) · 5701
DOI: 10.3390/ma17235701 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 21.11.2024. Verfasst von Sabry Fayed und 5 weiteren Autor:innen. Beteiligte Einrichtung: Civil Engineering Department, Faculty of Engineering, Kafrelsheikh University, Kafr El-Sheikh 33516, Egypt. Die Arbeit wurde bisher 40-mal zitiert (Crossref) und nennt 59 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Incheon National University, Incheon National University (International Cooperative) Research.
Abstract (Originalsprache)
In this study, shear-critical reinforced concrete (RC) beams were strengthened by combining the prestressing and near-surface mounted (NSM) rods approaches. The potential danger of failure in such RC beams is a substantial concern as it is considered a potential threat. This study addresses its careful mitigation through experimental identification and numerical analysis to enhance the safety and sustainability of buildings by reducing the probability of failure risk for these RC beams. Nine of the ten RC beams that were tested had strengthened, and one had not. Internal prestressing (IP) within the beam body, external prestressing NSM (PNSM), internal embedment (IE) inside the beam with or without prestressing, and NSM are the strengthening technologies that were employed. The range of the extra shear reinforcement ratios (μs) was 0.87% to 1.60%. We investigated how strengthened beams behaved structurally in terms of the cracking load, ultimate load, load–deflection response, ultimate deflection, and stiffness. The insertion of five pairs of PNSM rods (μs = 1.45%) and five pairs of IP rods (μs = 1.6%), respectively, increased the beams’ shear capacity by 57.8% and 70.4%. Shear capacity increased by 23.2% when three pairs of IE rods (μs = 1.02%) were installed. The prestressing location had an impact on shear capacity, with the interior case surpassing the external one. Compared to the control, the stiffness of the strengthened beams rose by 20%, 82%, and 84.4% when three, four, or five pairs of internal prestressing rods were added. A formula is proposed to calculate the shear capacity of all beams strengthened using various methods.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Civil Engineering Department, Faculty of Engineering, Kafrelsheikh University, Kafr El-Sheikh 33516, Egypt.
- Department of Civil and Environmental Engineering, Incheon National University, Incheon 22012, Republic of Korea.
- Incheon Disaster Prevention Research Center, Incheon National University, Incheon 22012, Republic of Korea.
- Department of Civil Engineering, College of Engineering and Architecture, Umm Al-Qura University, Makkah 24382, Saudi Arabia.
- Department of Civil Engineering, Faculty of Engineering, Al-Baha University, Al-Baha 65779, Saudi Arabia.
- Department of Civil Engineering, Higher Institute of Engineering and Technology, Kafr El-Sheikh 35516, Egypt.
ORCID-Profile: Jong Wan Hu, Abdullah Albogami, Saad A Yehia
Förderung
- Incheon National University
- Incheon National University (International Cooperative) Research
Zitieren
APA
Fayed, S., Ghalla, M., Hu, J. W., Mlybari, E. A., Albogami, A., & Yehia, S. A. (2024). Shear Strengthening of RC Beams Using Prestressed Near-Surface Mounted Bars Reducing the Probability of Construction Failure Risk. Materials, 17(23), 5701. https://doi.org/10.3390/ma17235701
Vancouver
Fayed S, Ghalla M, Hu JW, Mlybari EA, Albogami A, Yehia SA. Shear Strengthening of RC Beams Using Prestressed Near-Surface Mounted Bars Reducing the Probability of Construction Failure Risk. Materials. 2024;17(23):5701. doi:10.3390/ma17235701
BibTeX
@article{Fayed2024,
author = {Fayed, Sabry and Ghalla, Mohamed and Hu, Jong Wan and Mlybari, Ehab A and Albogami, Abdullah and Yehia, Saad A},
title = {Shear Strengthening of RC Beams Using Prestressed Near-Surface Mounted Bars Reducing the Probability of Construction Failure Risk},
journal = {Materials},
year = {2024},
volume = {17},
number = {23},
pages = {5701},
doi = {10.3390/ma17235701}
}
EUVIMED