Performance-Based Design of Ferronickel Slag Alkali-Activated Concrete for High Thermal Load Applications
Materials · 09.10.2024 · 17 (19) · 4939
DOI: 10.3390/ma17194939 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 09.10.2024. Verfasst von Andres Arce und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Civil Engineering, University of Patras, GR-26504 Patras, Greece. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union, Swiss Federal Institute of Technology.
Abstract (Originalsprache)
This study aimed to develop optimized alkali-activated concrete using ferronickel slag for high-temperature applications, focusing on minimizing environmental impact while maintaining high compressive strength and slump. A response surface methodology, specifically the mixture design of experiments, was employed to optimize five components: water, FNS-based alkali-activated binder, and three aggregate sizes. Twenty concrete mixes were tested for slump and compressive strength before and after exposure to 600 °C for two hours. The optimal mix achieved 88 MPa compressive strength before heat exposure and 34 MPa after, with a slump of 140 mm. An upscaled version with improved workability (210 mm slump) maintained similar unheated strength but showed reduced post-heating strength (23.5 MPa). Replacing limestone with olivine aggregates in the upscaled mix resulted in 65 MPa unheated and 32 MPa post-heating strengths. Life Cycle Analysis revealed that the optimized ferronickel slag alkali-activated concrete’s CO2 emissions were 77% lower than those of ordinary Portland cement concrete of equivalent strength. This approach demonstrated the applicability of mixture design of experiments as an alternative design methodology for alkali activated concrete, providing a valuable performance-based design tool to advance the application of alkali-activated concrete in the construction industry, where no prescriptive standards for alkali-activated ferronickel concrete mix design exist. The study concluded that the developed ferronickel slag alkali-activated concrete, obtained through a performance-based mixture design methodology, offers a promising, environmentally friendly alternative for high-strength, high-temperature applications in construction.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Civil Engineering, University of Patras, GR-26504 Patras, Greece.
- Department of Civil, Environmental and Geomatic Engineering, ETH Zurich, 8093 Zürich, Switzerland.
ORCID-Profile: Andres Arce, Anastasija Komkova, Catherine G Papanicolaou, Thanasis C Triantafillou
Förderung
- European Union
- Swiss Federal Institute of Technology
Zitieren
APA
Arce, A., Komkova, A., Papanicolaou, C. G., & Triantafillou, T. C. (2024). Performance-Based Design of Ferronickel Slag Alkali-Activated Concrete for High Thermal Load Applications. Materials, 17(19), 4939. https://doi.org/10.3390/ma17194939
Vancouver
Arce A, Komkova A, Papanicolaou CG, Triantafillou TC. Performance-Based Design of Ferronickel Slag Alkali-Activated Concrete for High Thermal Load Applications. Materials. 2024;17(19):4939. doi:10.3390/ma17194939
BibTeX
@article{Arce2024,
author = {Arce, Andres and Komkova, Anastasija and Papanicolaou, Catherine G and Triantafillou, Thanasis C},
title = {Performance-Based Design of Ferronickel Slag Alkali-Activated Concrete for High Thermal Load Applications},
journal = {Materials},
year = {2024},
volume = {17},
number = {19},
pages = {4939},
doi = {10.3390/ma17194939}
}
EUVIMED