EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Analysis of Mechanical Properties: Conventional vs. Additive Manufacturing for Stainless Steel 316L

Constantin Alex Sumanariu iD, Cătălin Gheorghe Amza iD, Florin Baciu iD, Mihai Ion Vasile, Adrian Ionut Nicoara iD

Materials · 29.09.2024 · 17 (19) · 4808

DOI: 10.3390/ma17194808 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 29.09.2024. Verfasst von Constantin Alex Sumanariu und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Quality Engineering and Industrial Technologies, Faculty of Industrial Engineering and Robotics, National University of Science and Tec…. Die Arbeit wurde bisher 40-mal zitiert (Crossref) und nennt 21 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This research investigates the tensile strength and microstructural properties of stainless steel 316L, comparing samples fabricated using additive manufacturing (AM) to those produced via conventional manufacturing techniques such as forging and casting using stainless steel 316L for its mechanical performance and corrosion resistance. Tensile tests revealed that AM samples had an ultimate tensile strength (UTS) of 650 MPa, a yield strength of 550 MPa and an elongation at break of 20%, and conventionally manufactured samples achieved a UTS of 580 MPa, a yield strength of 450 MPa and a higher elongation at break of 35%. The reduced ductility of AM samples is offset by their higher strength. Scanning electron microscopy (SEM) analysis showed that AM samples had a refined grain structure, with grain sizes ranging from 1 to 5 µm, whereas conventionally produced samples exhibited larger grain sizes of 10 to 20 µm, contributing to their increased ductility. This shows that while AM processes can give a rather high strength, the ductility property is simpler to attain with casting. Further work is needed to investigate post-processing techniques like hot isotropic pressing (HIP) and heat treatments for enhancing the ductility of AM parts as well as mechanical properties.

Schlagwörter

Stichwörter der Autor:innen

SEM analysisadditive manufacturingconventional manufacturingmechanical propertiesmicrostructural analysisstainless steel 316Ltensile strength

Autor:innen und Institutionen

  • Department of Quality Engineering and Industrial Technologies, Faculty of Industrial Engineering and Robotics, National University of Science and Technology POLITEHNICA Bucharest, 060042 București, Romania.
  • Department of Strength Materials, Faculty of Industrial Engineering and Robotics, National University of Science and Technology POLITEHNICA Bucharest, 060042 București, Romania.
  • Department of Science and Engineering of Oxide Materials and Nanomaterials, Faculty of Applied Chemistry and Materials Science, National University of Science and Technology POLITEHNICA Bucharest, 060042 București, Roma…

ORCID-Profile: Constantin Alex Sumanariu, Cătălin Gheorghe Amza, Florin Baciu, Adrian Ionut Nicoara

Zitieren

APA

Sumanariu, C. A., Amza, C. G., Baciu, F., Vasile, M. I., & Nicoara, A. I. (2024). Comparative Analysis of Mechanical Properties: Conventional vs. Additive Manufacturing for Stainless Steel 316L. Materials, 17(19), 4808. https://doi.org/10.3390/ma17194808

Vancouver

Sumanariu CA, Amza CG, Baciu F, Vasile MI, Nicoara AI. Comparative Analysis of Mechanical Properties: Conventional vs. Additive Manufacturing for Stainless Steel 316L. Materials. 2024;17(19):4808. doi:10.3390/ma17194808

BibTeX
@article{Sumanariu2024,
  author = {Sumanariu, Constantin Alex and Amza, Cătălin Gheorghe and Baciu, Florin and Vasile, Mihai Ion and Nicoara, Adrian Ionut},
  title = {Comparative Analysis of Mechanical Properties: Conventional vs. Additive Manufacturing for Stainless Steel 316L},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {19},
  pages = {4808},
  doi = {10.3390/ma17194808}
}
Kostenlos starten →