EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Thermal Annealing Effect on Elastoplastic Behaviour of Al/Cu Bimetal during Three-Point Bending

Robert Uścinowicz

Materials · 21.09.2024 · 17 (18) · 4637

DOI: 10.3390/ma17184637 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 21.09.2024. Verfasst von Robert Uścinowicz. Beteiligte Einrichtung: Department of Mechanics and Applied Computer Science, Faculty of Mechanical Engineering, Bialystok University of Technology, 45C Wiejska, 15-351 Bial…. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bialystok University of Technology, Polish Ministry of Science and Higher Education, National Science Centre of Poland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents the results of experimental studies on the effects of temperature and time of annealing on the elastoplastic properties of bimetallic aluminium–copper sheets. Mechanical tests were carried out on flat samples previously heated to temperatures of 250, 350, 450, and 500 °C for 40, 90, and 150 min. At the beginning of the tests, the elastic constants and internal friction energy were determined after thermal exposure using the impulse vibration exposure method. Further tests were carried out on the same samples using the three-point bending test. Based on the tests, the following quantities were determined and analysed: elasticity angles, translocations of the neutral axes of the cross-sections of samples, and changes in the values of bending moments plasticizing the extreme layers of bimetallic Al/Cu samples resulting from thermal interactions. The final part of this paper presents the results of measurements of the thickness of diffusion zones at the interface and their effect on the stability of the joint after annealing. The studies that were conducted indicate the dominant influence of the thermal factor on the properties of the Al/Cu bimetal above the temperature of 350 °C, which leads to the weakening of its strength and the degradation of the structure at the metallic phase boundary.

Schlagwörter

Stichwörter der Autor:innen

Al/Cu bimetalelastic constantselastoplastic deformationmicrographyspringbackthermal annealingthree-point bending test

Autor:innen und Institutionen

  • Department of Mechanics and Applied Computer Science, Faculty of Mechanical Engineering, Bialystok University of Technology, 45C Wiejska, 15-351 Bialystok, Poland.

Förderung

  • Bialystok University of Technology
  • Polish Ministry of Science and Higher Education
  • National Science Centre of Poland

Zitieren

APA

Uścinowicz, R. (2024). Thermal Annealing Effect on Elastoplastic Behaviour of Al/Cu Bimetal during Three-Point Bending. Materials, 17(18), 4637. https://doi.org/10.3390/ma17184637

Vancouver

Uścinowicz R. Thermal Annealing Effect on Elastoplastic Behaviour of Al/Cu Bimetal during Three-Point Bending. Materials. 2024;17(18):4637. doi:10.3390/ma17184637

BibTeX
@article{Ucinowicz2024,
  author = {Uścinowicz, Robert},
  title = {Thermal Annealing Effect on Elastoplastic Behaviour of Al/Cu Bimetal during Three-Point Bending},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {18},
  pages = {4637},
  doi = {10.3390/ma17184637}
}
Kostenlos starten →