EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure, Mechanical, and Tribological Properties of Nb-Doped TiAl Alloys Fabricated via Laser Metal Deposition

Kai Huang, Feng Xu, Xinyan Liu, Shiqiu Liu, Qingge Wang iD, Ian Baker iD, Min Song iD, Hong Wu

Materials · 28.08.2024 · 17 (17) · 4260

DOI: 10.3390/ma17174260 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 28.08.2024. Verfasst von Kai Huang und 7 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 62 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the National Natural Science Foundation of China, Natural Science Foundation of Hunan Province for Distinguished Young Scholars, Scientific and Technological Project of Yunnan Precious Metals Laboratory.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

TiAl alloys possess excellent properties, such as low density, high specific strength, high elastic modulus, and high-temperature creep resistance, which allows their use to replace Ni-based superalloys in some high-temperature applications. In this work, the traditional TiAl alloy Ti-48Al-2Nb-2Cr (Ti4822) was alloyed with additional Nb and fabricated using laser metal deposition (LMD), and the impacts of this additional Nb on the microstructure and mechanical and tribological properties of the as-fabricated alloys were investigated. The resulting alloys mainly consisted of the γ phase, trace β0 and α2 phases. Nb was well distributed throughout the alloys, while Cr segregation resulted in the residual β0 phase. Increasing the amount of Nb content increased the amount of the γ phase and reduced the amount of the β0 phase. The alloy Ti4822-2Nb exhibited a room-temperature (RT) fracture strength under a tensile of 568 ± 7.8 MPa, which was nearly 100 MPa higher than that of the Ti4822-1Nb alloy. A further increase in Nb to an additional 4 at.% Nb had little effect on the fracture strength. Both the friction coefficient and the wear rate increased with the increasing Nb content. The wear mechanisms for all samples were abrasive wear with local plastic deformation and oxidative wear, resulting in the formation of metal oxide particles.

Schlagwörter

Stichwörter der Autor:innen

Nb alloyingTiAl alloyslaser metal depositionmechanical propertiesmicrostructuretribological properties

Autor:innen und Institutionen

  • State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China.
  • Farsoon Technologies Co., Ltd., Changsha 410221, China.
  • Advanced Materials Additive Manufacturing Innovation Research Center, School of Engineering, Hangzhou City University, Hangzhou 310015, China.
  • Thayer School of Engineering, Dartmouth College, Hanover, NH 03755, USA.

ORCID-Profile: Qingge Wang, Ian Baker, Min Song

Förderung

  • the National Natural Science Foundation of China
  • Natural Science Foundation of Hunan Province for Distinguished Young Scholars
  • Scientific and Technological Project of Yunnan Precious Metals Laboratory
  • Central South University Research Program of Advanced Interdisciplinary Studies
  • National Natural Science Foundation of China

Zitieren

APA

Huang, K., Xu, F., Liu, X., Liu, S., Wang, Q., Baker, I., Song, M., & Wu, H. (2024). Microstructure, Mechanical, and Tribological Properties of Nb-Doped TiAl Alloys Fabricated via Laser Metal Deposition. Materials, 17(17), 4260. https://doi.org/10.3390/ma17174260

Vancouver

Huang K, Xu F, Liu X, Liu S, Wang Q, Baker I, et al. Microstructure, Mechanical, and Tribological Properties of Nb-Doped TiAl Alloys Fabricated via Laser Metal Deposition. Materials. 2024;17(17):4260. doi:10.3390/ma17174260

BibTeX
@article{Huang2024,
  author = {Huang, Kai and Xu, Feng and Liu, Xinyan and Liu, Shiqiu and Wang, Qingge and Baker, Ian and Song, Min and Wu, Hong},
  title = {Microstructure, Mechanical, and Tribological Properties of Nb-Doped TiAl Alloys Fabricated via Laser Metal Deposition},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {17},
  pages = {4260},
  doi = {10.3390/ma17174260}
}
Kostenlos starten →