EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Solder Mask on Electrochemical Migration on Printed Circuit Boards

Markéta Klimtová iD, Petr Veselý iD, Iva Králová iD, Karel Dušek

Materials · 27.08.2024 · 17 (17) · 4242

DOI: 10.3390/ma17174242 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.08.2024. Verfasst von Markéta Klimtová und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Electrotechnology, Faculty of Electrical Engineering, Czech Technical University in Prague, Technická 2, 160 00 Prague, Czech Republic. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Czech Technical University in Prague, Internal Grant Agency of the Czech Technical University in Prague.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Electrochemical migration (ECM) on the surface of printed circuit boards (PCBs) continues to pose a significant reliability risk in electronics. Nevertheless, the existing literature lacks studies that address the solder mask and solder pad design aspects in the context of ECM. Therefore, the objective of this study was to assess the impact of solder mask type with varying roughness and solder pad design on the susceptibility to ECM using a water drop test and thermal humidity bias test. Hot air solder leveling-coated PCBs were tested. Furthermore, the ECM tests were conducted on PCBs with applied no-clean solder paste to evaluate the influence of flux residues on the resulting ECM behavior. The results indicated that the higher roughness of the solder mask significantly contributes to ECM inhibition through the creation of a mechanical barrier for the dendrites. Furthermore, lower ECM susceptibility was also observed for copper-defined pads, where a similar effect is presumed. However, the influence of the no-clean flux residues can prevail over the effects of the solder mask. Therefore, the use of a rough solder mask and a copper-defined pad design is recommended if the PCB is to be washed from flux residues after the soldering process.

Schlagwörter

Stichwörter der Autor:innen

dendriteselectrochemical migrationsolder maskthermal humidity bias testwater drop test

Autor:innen und Institutionen

  • Department of Electrotechnology, Faculty of Electrical Engineering, Czech Technical University in Prague, Technická 2, 160 00 Prague, Czech Republic.

ORCID-Profile: Markéta Klimtová, Petr Veselý, Iva Králová

Förderung

  • Czech Technical University in Prague
  • Internal Grant Agency of the Czech Technical University in Prague

Zitieren

APA

Klimtová, M., Veselý, P., Králová, I., & Dušek, K. (2024). Influence of Solder Mask on Electrochemical Migration on Printed Circuit Boards. Materials, 17(17), 4242. https://doi.org/10.3390/ma17174242

Vancouver

Klimtová M, Veselý P, Králová I, Dušek K. Influence of Solder Mask on Electrochemical Migration on Printed Circuit Boards. Materials. 2024;17(17):4242. doi:10.3390/ma17174242

BibTeX
@article{Klimtov2024,
  author = {Klimtová, Markéta and Veselý, Petr and Králová, Iva and Dušek, Karel},
  title = {Influence of Solder Mask on Electrochemical Migration on Printed Circuit Boards},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {17},
  pages = {4242},
  doi = {10.3390/ma17174242}
}
Kostenlos starten →