EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Evaluation of the Properties of 3D-Printed Onyx–Fiberglass Composites

Jong-Hwan Yun iD, Gun-Woong Yoon, Yu-Jae Jeon, Min-Soo Kang iD

Materials · 21.08.2024 · 17 (16) · 4140

DOI: 10.3390/ma17164140 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 21.08.2024. Verfasst von Jong-Hwan Yun und 3 weiteren Autor:innen. Beteiligte Einrichtung: Regional Innovation Platform Project of Kongju National University, Kongju National University, Cheonan 31080, Republic of Korea. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: This research was supported by "Regional Innovation Strategy (RIS)" through the National Re-search Foundation of Korea(NRF) funded by the Ministry of Education…, This work was supported by the Sun Moon University Research Grant of 2021., Ministry of Education (MOE).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluated the properties of 3D-printed Onyx–fiberglass composites. These composites were 3D-printed with zero, one, two, three, and four layers of fiberglass. Ten samples of each configuration were printed for the tensile and flexural tests. The average tensile strength of the Onyx specimens was calculated to be 44.79 MPa, which increased linearly by approximately 20–25 MPa with each additional fiberglass layer. The elastic moduli calculated from the micromechanics models were compared with the experimental values obtained from the tensile tests. The experimental elastic modulus increased more significantly than the model prediction when more fiberglass layers were added. The flexural modulus of Onyx was 17.6 GPa, which increased with each additional fiberglass layer. This quantitative analysis of composites fabricated using 3D printing highlights their potential for commercialization and industrial applications.

Schlagwörter

Stichwörter der Autor:innen

3-point bending test3D printingcompositefiberglassonyxtensile test

Autor:innen und Institutionen

  • Regional Innovation Platform Project of Kongju National University, Kongju National University, Cheonan 31080, Republic of Korea.
  • Division of Smart Automotive Engineering, Sun Moon University, Asan 31460, Republic of Korea.
  • Department of Medical Rehabilitation Science, Yeoju Institute of Technology, Yeoju 12652, Republic of Korea.

ORCID-Profile: Jong-Hwan Yun, Min-Soo Kang

Förderung

  • This research was supported by "Regional Innovation Strategy (RIS)" through the National Re-search Foundation of Korea(NRF) funded by the Ministry of Education…
  • This work was supported by the Sun Moon University Research Grant of 2021.
  • Ministry of Education (MOE)
  • Sun Moon University Research Grant of 2021

Zitieren

APA

Yun, J. H., Yoon, G. W., Jeon, Y. J., & Kang, M. S. (2024). Evaluation of the Properties of 3D-Printed Onyx–Fiberglass Composites. Materials, 17(16), 4140. https://doi.org/10.3390/ma17164140

Vancouver

Yun JH, Yoon GW, Jeon YJ, Kang MS. Evaluation of the Properties of 3D-Printed Onyx–Fiberglass Composites. Materials. 2024;17(16):4140. doi:10.3390/ma17164140

BibTeX
@article{Yun2024,
  author = {Yun, Jong-Hwan and Yoon, Gun-Woong and Jeon, Yu-Jae and Kang, Min-Soo},
  title = {Evaluation of the Properties of 3D-Printed Onyx–Fiberglass Composites},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {16},
  pages = {4140},
  doi = {10.3390/ma17164140}
}
Kostenlos starten →