Vat Photopolymerization of Ceramic Parts: Effects of Carbon Fiber Additives on Microstructure and Mechanical Performance
Materials · 26.06.2024 · 17 (13) · 3127
DOI: 10.3390/ma17133127 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 26.06.2024. Verfasst von Lu Wang und 10 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Automotive Engineering, Liaocheng University, Liaocheng 252000, China. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Shandong Provincial Natural Science Foundation, Training Program of Innovation and Entrepreneurship for Undergraduates.
Abstract (Originalsprache)
Vat photopolymerization (VPP), as an additive manufacturing (AM) technology, can conveniently produce ceramic parts with high resolution and excellent surface quality. However, due to the inherent brittleness and low toughness of ceramic materials, manufacturing defect-free ceramic parts remains a challenge. Many researchers have attempted to use carbon fibers as additives to enhance the performance of ceramic parts, but these methods are mostly applied in processes like fused deposition modeling and hot pressing. To date, no one has applied them to VPP-based AM technology. This is mainly because the black carbon fibers reduce laser penetration, making it difficult to cure the ceramic slurry and thus challenging to produce qualified ceramic parts. To address this issue, our study has strictly controlled the amount of carbon fibers by incorporating trace amounts of carbon fiber powder into the original ceramic slurry with the aim to investigate the impact of these additions on the performance of ceramic parts. In this study, ceramic slurries with three different carbon fiber contents (0 wt.%, 0.1 wt.%, 0.2 wt.%, and 0.3 wt.%) were used for additive manufacturing. A detailed comparative analysis of the microstructure, physical properties, and mechanical performance of the parts was conducted. The experimental results indicate that the 3D-printed alumina parts with added carbon fibers show varying degrees of improvement in multiple performance parameters. Notably, the samples prepared with 0.2 wt.% carbon fiber content exhibited the most significant performance enhancements.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Mechanical and Automotive Engineering, Liaocheng University, Liaocheng 252000, China.
- Jiangsu Key Laboratory of Advanced Manufacturing Technology, Huaiyin Institute of Technology, Huaiyin 223003, China.
- School of Materials Science and Engineering, Shandong University, Jinan 250061, China.
ORCID-Profile: Anfu Guo, Zhong Chen
Förderung
- National Natural Science Foundation of China
- Shandong Provincial Natural Science Foundation
- Training Program of Innovation and Entrepreneurship for Undergraduates
- The Natural Science Foundation of Shandong Province
- The Training Program of Innovation and Entrepreneurship for Undergraduates
- the open fund for Jiangsu Key Laboratory of Advanced Manufacturing Technology
- Liaocheng University
Zitieren
APA
Wang, L., Wu, H., Guo, A., Kong, D., Zhao, Z., Liu, C., Yin, L., Xia, G., Su, X., Chen, Z., & Wang, D. (2024). Vat Photopolymerization of Ceramic Parts: Effects of Carbon Fiber Additives on Microstructure and Mechanical Performance. Materials, 17(13), 3127. https://doi.org/10.3390/ma17133127
Vancouver
Wang L, Wu H, Guo A, Kong D, Zhao Z, Liu C, et al. Vat Photopolymerization of Ceramic Parts: Effects of Carbon Fiber Additives on Microstructure and Mechanical Performance. Materials. 2024;17(13):3127. doi:10.3390/ma17133127
BibTeX
@article{Wang2024,
author = {Wang, Lu and Wu, Hailong and Guo, Anfu and Kong, Dekun and Zhao, Zhengyu and Liu, Chang and Yin, Lvfa and Xia, Guojun and Su, Xiaofei and Chen, Zhong and Wang, Diangang},
title = {Vat Photopolymerization of Ceramic Parts: Effects of Carbon Fiber Additives on Microstructure and Mechanical Performance},
journal = {Materials},
year = {2024},
volume = {17},
number = {13},
pages = {3127},
doi = {10.3390/ma17133127}
}
EUVIMED