Intercritically Annealed Medium-Manganese Steel: Insights into Microstructural and Microtextural Evolution, Strain Distribution, and Grain Boundary Characteristics
Materials · 05.06.2024 · 17 (11) · 2757
DOI: 10.3390/ma17112757 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 05.06.2024. Verfasst von Sudipta Mohapatra und 2 weiteren Autor:innen. Beteiligte Einrichtung: Division of Advanced Materials Engineering, Research Center of Advanced Material Development, Jeonbuk National University, Jeonju 54896, Republic of …. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 63 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Research Foundation of Korea (NRF) grant funded by the Korea Government (Ministry of Science and ICT). This work was also supported in part by the Tec…, Korea Government (Ministry of Science and ICT), Technology Development Program.
Abstract (Originalsprache)
Aluminum-incorporated medium-manganese steel (MMnS) has potential for lightweight transport applications owing to its impressive mechanical properties. Increasing the austenite volume fraction and making microstructural changes are key to manufacturing MMnS. However, the grain boundary character and strain distribution of intercritically annealed low-density MMnS have not been extensively scrutinized, and the effects of crystallographic texture orientation on tensile properties remain ambiguous. Therefore, in this study, the microstructure, microtexture, strain distribution, and grain boundary characteristics of a hot-rolled medium-Mn steel (Fe–0.2 C–4.3 Al–9.4 Mn (wt%)) were investigated after intercritical annealing (IA) at 750, 800, or 850 °C for 1 h. The results show that the 800 °C annealed sample exhibited the highest austenite volume fraction among the specimens (60%). The duplex microstructure comprised lath-type γ-austenite, fine α-ferrite, and coarse δ-ferrite. As the IA temperature increased, the body-centered cubic phase orientation shifted from to . At higher temperatures, the face-centered cubic phase was oriented in directions ranging from to , and the sums of the fractions of high-angle grain boundaries and coincidence–site–lattice special boundaries were significantly increased. The 800 °C annealed sample with a high austenite content and strong γ-fiber {111}//RD orientation demonstrated a noteworthy tensile strength (1095 MPa) and tensile elongation (30%).
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Division of Advanced Materials Engineering, Research Center of Advanced Material Development, Jeonbuk National University, Jeonju 54896, Republic of Korea.
- R&D Department, SAMWOOECO Co., Ltd., Gwangyang 57759, Republic of Korea.
ORCID-Profile: Sudipta Mohapatra
Förderung
- National Research Foundation of Korea (NRF) grant funded by the Korea Government (Ministry of Science and ICT). This work was also supported in part by the Tec…
- Korea Government (Ministry of Science and ICT)
- Technology Development Program
- Ministry of SMEs and Startups
Zitieren
APA
Mohapatra, S., Baek, K. C., & Oh, M. S. (2024). Intercritically Annealed Medium-Manganese Steel: Insights into Microstructural and Microtextural Evolution, Strain Distribution, and Grain Boundary Characteristics. Materials, 17(11), 2757. https://doi.org/10.3390/ma17112757
Vancouver
Mohapatra S, Baek KC, Oh MS. Intercritically Annealed Medium-Manganese Steel: Insights into Microstructural and Microtextural Evolution, Strain Distribution, and Grain Boundary Characteristics. Materials. 2024;17(11):2757. doi:10.3390/ma17112757
BibTeX
@article{Mohapatra2024,
author = {Mohapatra, Sudipta and Baek, Kyeong-Cheol and Oh, Min-Suk},
title = {Intercritically Annealed Medium-Manganese Steel: Insights into Microstructural and Microtextural Evolution, Strain Distribution, and Grain Boundary Characteristics},
journal = {Materials},
year = {2024},
volume = {17},
number = {11},
pages = {2757},
doi = {10.3390/ma17112757}
}
EUVIMED