Experimental Simulation of Directional Crystallization of SiMo Cast Iron Alloyed with Al and Cr
Materials · 28.05.2024 · 17 (11) · 2592
DOI: 10.3390/ma17112592 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 28.05.2024. Verfasst von Krzysztof Morgiel und 1 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Foundry Engineering, AGH University of Krakow, al. A. Mickiewicza 30, 30-059 Krakow, Poland. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
SiMo ductile cast iron combines ease of part fabrication with good mechanical properties, including a usable plasticity range. Its poor corrosion resistance inherited from grey cast iron could be alleviated through alloying with Al or Cr additions capable of forming a dense oxide scale protecting the substrate. However, the presence of Al and Cr in cast iron tends to make the material brittle, and their optimum alloying additions need to be studied further. The present work was aimed at investigating the effect of crystallization rates on microstructure changes during directional crystallization of SiMo-type alloys with up to 3.5% Al and 2.4% Cr. The experiment was performed using the Bridgman–Stockbarger method. The tubular crucible was transferred from the hot section to cold section at rates ranging from 5 mm/h to 30 mm/h with a 4/5 crucible length and then quenched. The introduced Al promoted graphitization up to a point, wherein, at the highest applied addition, the graphite precipitation preceded crystallization of the rest of the melt. A rising level of Cr in these alloys from 1% to 2.4% resulted in the formation of low and high contents of pearlite, respectively. The higher crystallization rates proved effective in increasing the ferrite content at the expense of pearlite. In the investigated cast iron samples with smaller applied alloying additions, Widmanstätten ferrite or ausferrite, i.e., fine acircular phase, were often found. The switch from directional crystallization to quenching caused a transition from a liquid to solid state, which started with nucleation of islands of fine austenite dendrites with chunky graphite eutectic separating them. As these islands expanded, they pushed alloying additions to their sides, promoting carbide or pearlite formation in these places and forming a super-cell-like structure. The performed experiments helped gather information concerning the sensitivity of the microstructure of SiMo cast iron modified with Al and Cr to crystallization rates prevailing in heavy cast structures.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Foundry Engineering, AGH University of Krakow, al. A. Mickiewicza 30, 30-059 Krakow, Poland.
ORCID-Profile: Krzysztof Morgiel, Dariusz Kopyciński
Zitieren
APA
Morgiel, K., & Kopyciński, D. (2024). Experimental Simulation of Directional Crystallization of SiMo Cast Iron Alloyed with Al and Cr. Materials, 17(11), 2592. https://doi.org/10.3390/ma17112592
Vancouver
Morgiel K, Kopyciński D. Experimental Simulation of Directional Crystallization of SiMo Cast Iron Alloyed with Al and Cr. Materials. 2024;17(11):2592. doi:10.3390/ma17112592
BibTeX
@article{Morgiel2024,
author = {Morgiel, Krzysztof and Kopyciński, Dariusz},
title = {Experimental Simulation of Directional Crystallization of SiMo Cast Iron Alloyed with Al and Cr},
journal = {Materials},
year = {2024},
volume = {17},
number = {11},
pages = {2592},
doi = {10.3390/ma17112592}
}
EUVIMED