EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Potential of Reusing 3D Printed Concrete (3DPC) Fine Recycled Aggregates as a Strategy towards Decreasing Cement Content in 3DPC

Szymon Skibicki iD, Karol Federowicz iD, Marcin Hoffmann, Mehdi Chougan iD, Daniel Sibera iD, Krzysztof Cendrowski iD, Mateusz Techman, João Nuno Pacheco, Maxime Liard, Pawel Sikora iD

Materials · 27.05.2024 · 17 (11) · 2580

DOI: 10.3390/ma17112580 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.05.2024. Verfasst von Szymon Skibicki und 9 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Civil and Environmental Engineering, West Pomeranian University of Technology in Szczecin, 70-310 Szczecin, Poland. Die Arbeit wurde bisher 39-mal zitiert (Crossref) und nennt 59 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Centre for Research and Development (NCBR), FCT - the Portuguese Foundation for Science and Technology, FCT—the Portuguese Foundation for Science and Technology.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper explores the new potential strategy of using fine recycled aggregates (fRA) derived from waste 3D printed concrete (3DPC) as a substitute for cement in additive manufacturing. This study hypothesizes that fRA can optimize mixture design, reduce cement content, and contribute to sustainable construction practices. Experimental programs were conducted to evaluate the fresh and hardened properties, printability window, and buildability of 3DPC mixes containing fRA. Mixes with replacement rates of cement with fRA by 10 vol%, 20 vol%, 30 vol%, 40 vol%, and 50 vol% were produced. A comprehensive experimental protocol consisting of rheological studies (static and dynamic yield stress), dynamic elastic modulus determination (first 24 h of hydration), flexural and compressive strengths (2 d and 28 d), and an open porosity test was performed. The obtained results were verified by printing tests. In addition, an economic and environmental life cycle assessment (LCA) of the mixes was performed. The results indicate that up to 50 vol% cement replacement with fRA is feasible, albeit with some technical drawbacks. While fRA incorporation enhances sustainability by reducing CO2 emissions and material costs, it adversely affects the printability window, green strength, setting time, and mechanical properties, particularly in the initial curing stages. Therefore, with higher replacement rates (above 20 vol%), potential optimization efforts are needed to mitigate drawbacks such as reduced green strength and buildability. Notably, replacement rates of up to 20 vol% can be successfully used without compromising the overall material properties or altering the mixture design. The LCA analysis shows that reducing the cement content and increasing the fRA addition results in a significant reduction in mix cost (up to 24%) and a substantial decrease in equivalent CO2 emissions (up to 48%). In conclusion, this study underscores the potential of fRA as a sustainable alternative to cement in 3D printed concrete.

Schlagwörter

Stichwörter der Autor:innen

3D concrete printing3DPCadditive manufacturingconcretegreen strengthrecycled aggregaterheologywaste aggregate

Autor:innen und Institutionen

  • Faculty of Civil and Environmental Engineering, West Pomeranian University of Technology in Szczecin, 70-310 Szczecin, Poland.
  • Faculty of Mechanical Engineering and Mechatronics, West Pomeranian University of Technology in Szczecin, 70-310 Szczecin, Poland.
  • Department of Civil and Environmental Engineering, Brunel University London, Uxbridge UB8 3PH, UK.
  • CERIS/c5Lab-Sustainable Construction Materials Association, Edifício Central Park, Rua Central Park 6, 2795-242 Linda-a-Velha, Portugal.
  • Sika Technology AG-Central Research, Tüffenwies 16, 8064 Zurich, Switzerland.

ORCID-Profile: Szymon Skibicki, Karol Federowicz, Mehdi Chougan, Daniel Sibera, Krzysztof Cendrowski, Pawel Sikora

Förderung

  • National Centre for Research and Development (NCBR)
  • FCT - the Portuguese Foundation for Science and Technology
  • FCT—the Portuguese Foundation for Science and Technology

Zitieren

APA

Skibicki, S., Federowicz, K., Hoffmann, M., Chougan, M., Sibera, D., Cendrowski, K., Techman, M., Pacheco, J. N., Liard, M., & Sikora, P. (2024). Potential of Reusing 3D Printed Concrete (3DPC) Fine Recycled Aggregates as a Strategy towards Decreasing Cement Content in 3DPC. Materials, 17(11), 2580. https://doi.org/10.3390/ma17112580

Vancouver

Skibicki S, Federowicz K, Hoffmann M, Chougan M, Sibera D, Cendrowski K, et al. Potential of Reusing 3D Printed Concrete (3DPC) Fine Recycled Aggregates as a Strategy towards Decreasing Cement Content in 3DPC. Materials. 2024;17(11):2580. doi:10.3390/ma17112580

BibTeX
@article{Skibicki2024,
  author = {Skibicki, Szymon and Federowicz, Karol and Hoffmann, Marcin and Chougan, Mehdi and Sibera, Daniel and Cendrowski, Krzysztof and Techman, Mateusz and Pacheco, João Nuno and Liard, Maxime and Sikora, Pawel},
  title = {Potential of Reusing 3D Printed Concrete (3DPC) Fine Recycled Aggregates as a Strategy towards Decreasing Cement Content in 3DPC},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {11},
  pages = {2580},
  doi = {10.3390/ma17112580}
}
Kostenlos starten →