Ultrasonic Non-Destructive Detection Method for Residual Stress in Rotary Forging Aluminum Alloy Plates
Materials · 24.05.2024 · 17 (11) · 2528
DOI: 10.3390/ma17112528 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 24.05.2024. Verfasst von Hongyu Chen und 4 weiteren Autor:innen. Beteiligte Einrichtung: Hubei Key Laboratory of Advanced Technology for Automotive Components, Wuhan University of Technology, Wuhan 430070, China. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Wuhan East Lake New Technology Development Zone “open list” project, Innovative Research Team Development Program of the Ministry of Education of China.
Abstract (Originalsprache)
Aluminum alloy plates are widely used to manufacture large-scale integral structure parts in the field of aerospace. During the forming and processing of aluminum alloy plates, different degrees of residual stress are inevitably produced. Fast and accurate detection of residual stress is very essential to ensuring the quality of these plates. In this work, the longitudinal critically refracted (LCR) wave detection method based on a one-transmitter and double-receiver (OTDR) transducer and the finite element simulation were employed to obtain the residual stress. Aluminum alloy plates with different deformation amounts were fabricated by rotary forging to obtain different residual stress states. Results reveal that the plate formed by rotary forging is in a stress state of central tension and edge compression. As the deformation increases from 20% to 60%, the peak residual tensile stress increases from 156 MPa to 262 MPa, and there is no significant difference in the peak compressive stress. When the deformation reaches 60%, the difference in the residual stresses at different depths is less than 13%, which indicates that the plastic deformation zone basically penetrates the entire longitudinal cross-section of the plate. The maximum deviation between measurement and FE is 61 MPa, which means the experimental data are in good agreement with the FE results.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Hubei Key Laboratory of Advanced Technology for Automotive Components, Wuhan University of Technology, Wuhan 430070, China.
- Hubei Collaborative Innovation Center for Automotive Components Technology, Wuhan University of Technology, Wuhan 430070, China.
- School of Automotive Engineering, Wuhan University of Technology, Wuhan 430070, China.
Förderung
- National Natural Science Foundation of China
- Wuhan East Lake New Technology Development Zone “open list” project
- Innovative Research Team Development Program of the Ministry of Education of China
- 111 Project
Zitieren
APA
Chen, H., Wang, X., Han, X., Zheng, F., & Yan, W. (2024). Ultrasonic Non-Destructive Detection Method for Residual Stress in Rotary Forging Aluminum Alloy Plates. Materials, 17(11), 2528. https://doi.org/10.3390/ma17112528
Vancouver
Chen H, Wang X, Han X, Zheng F, Yan W. Ultrasonic Non-Destructive Detection Method for Residual Stress in Rotary Forging Aluminum Alloy Plates. Materials. 2024;17(11):2528. doi:10.3390/ma17112528
BibTeX
@article{Chen2024,
author = {Chen, Hongyu and Wang, Xiaokai and Han, Xinghui and Zheng, Fangyan and Yan, Wenlong},
title = {Ultrasonic Non-Destructive Detection Method for Residual Stress in Rotary Forging Aluminum Alloy Plates},
journal = {Materials},
year = {2024},
volume = {17},
number = {11},
pages = {2528},
doi = {10.3390/ma17112528}
}
EUVIMED