EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Methodology of Chip Temperature Measurement and Safety Machining Assessment in Dry Rough Milling of Magnesium Alloys Using Different Helix Angle Tools

Ireneusz Zagórski iD, Piotr Zgórniak iD, Witold Habrat iD, José Machado iD, Stanisław Legutko iD

Materials · 27.04.2024 · 17 (9) · 2063

DOI: 10.3390/ma17092063 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.04.2024. Verfasst von Ireneusz Zagórski und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Production Engineering, Mechanical Engineering Faculty, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Education and Science: VIA CARPATIA Universities of Technology Network named after the President of the Republic of Poland Lech Kaczyński.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents the methodology of measuring chip temperature in the cutting zone in the rough milling of magnesium alloys. Infrared measurements are taken to determine the effect of variable cutting speed, feed per tooth, and depth of cut on the maximum temperature of chips. Thermal images of chip temperature for a generated collective frame and corresponding histograms are presented. Chip temperatures are presented in numerical terms as median and average values; maximum and minimum values; range; and standard deviation. Box plots are also shown for selected machining conditions. The problems arising during signal recording with a mean emissivity coefficient ε = 0.13, a value which is dedicated during machining magnesium alloys, are discussed in detail. Chip temperatures obtained in the tests do not exceed approx. 420 °C. Therefore, the dry rough milling process carried out with carbide tools with different blade geometries can be considered safe for a wide range of machining parameters. The proposed methodology of chip temperature measurement and result processing is a new and effective approach to safety assessment in the dry milling of magnesium alloys.

Schlagwörter

Stichwörter der Autor:innen

carbide toolschip temperaturehelix angleinfrared measurementmagnesium alloysrough millingtemperature in cutting zone

Autor:innen und Institutionen

  • Department of Production Engineering, Mechanical Engineering Faculty, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland.
  • Institute of Machine Tools and Production Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, Stefanowskiego 1/15, 90-537 Łódź, Poland.
  • Department of Manufacturing and Automation Technologies, Rzeszow University of Technology, Powstańców Warszawy 12, 35-959 Rzeszów, Poland.
  • MEtRCs Research Center, Campus of Azurém, University of Minho, 4800-058 Guimarães, Portugal.
  • Institute of Mechanical Technology, Faculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 2, 61-138 Poznań, Poland.

ORCID-Profile: Ireneusz Zagórski, Piotr Zgórniak, Witold Habrat, José Machado, Stanisław Legutko

Förderung

  • Ministry of Education and Science: VIA CARPATIA Universities of Technology Network named after the President of the Republic of Poland Lech Kaczyński

Zitieren

APA

Zagórski, I., Zgórniak, P., Habrat, W., Machado, J., & Legutko, S. (2024). Methodology of Chip Temperature Measurement and Safety Machining Assessment in Dry Rough Milling of Magnesium Alloys Using Different Helix Angle Tools. Materials, 17(9), 2063. https://doi.org/10.3390/ma17092063

Vancouver

Zagórski I, Zgórniak P, Habrat W, Machado J, Legutko S. Methodology of Chip Temperature Measurement and Safety Machining Assessment in Dry Rough Milling of Magnesium Alloys Using Different Helix Angle Tools. Materials. 2024;17(9):2063. doi:10.3390/ma17092063

BibTeX
@article{Zagrski2024,
  author = {Zagórski, Ireneusz and Zgórniak, Piotr and Habrat, Witold and Machado, José and Legutko, Stanisław},
  title = {Methodology of Chip Temperature Measurement and Safety Machining Assessment in Dry Rough Milling of Magnesium Alloys Using Different Helix Angle Tools},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {9},
  pages = {2063},
  doi = {10.3390/ma17092063}
}
Kostenlos starten →