Preparation of Ultrafine Co- and Ni-Coated (Ti,W,Mo,Ta)(C,N) Powders and Their Influence on the Microstructure of Ti(C,N)-Based Cermets
Materials · 15.04.2024 · 17 (8) · 1807
DOI: 10.3390/ma17081807 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 15.04.2024. Verfasst von Zaiyang Zhao und 6 weiteren Autor:innen. Beteiligte Einrichtung: Fujian Province Key Laboratory of Functional Materials and Applications, Xiamen University of Technology, Xiamen 361024, China. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Lili Ma, Natural Science Foundation of Fujian Provincial of China, Scientific Research Climbing Project of Xiamen University of Technology.
Abstract (Originalsprache)
The use of metal-coated ceramic powders not only effectively enhances the wettability of the metal–ceramic interface but also promotes a more uniform microstructure in Ti(C,N)-based cermets, which is advantageous for improving their mechanical properties. In this study, ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders were synthesized via the spray-drying-in-situ carbothermal reduction method. Subsequently, Ti(C,N)-based cermets were effectively fabricated using the as-prepared ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders. The impact of reaction temperature, heating rate, and isothermal time on the phase and microstructure of prepared powders was analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Additionally, the microstructure of the as-sintered cermets was experimentally investigated. The findings reveal that the complete reduction of Co and Ni metal salts, pre-coated on the surface of (Ti,W,Mo,Ta)(C,N) particles, can be achieved through rapid heating (10 °C/min) in a specific temperature range (600–1000 °C) with an isothermal time of 3 h at a lower reduction temperature (1000 °C). The synthesized powders have only two phases: the (Ti,W,Mo,Ta)(C,N) phase and Co/Ni phase, and no other heterogeneous phases were observed with an oxygen content of 0.261 wt.%. Notably, the conventional core–rim structure was not dominant in the cermets obtained from the prepared Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders. Moreover, the heterogeneous segregation effect of the Co/Ni coating on the ultrafine powder particles resulted in a finer microstructure than the traditional cermets with the same composition. However, the grain size is mainly in the range of 0.5–0.8 μm. The weaker residual stresses at the core and rim interfaces and the finer particle distributions could theoretically enhance the toughness of Ti(C,N)-based cermets, simultaneously.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Fujian Province Key Laboratory of Functional Materials and Applications, Xiamen University of Technology, Xiamen 361024, China.
- School of Materials Science and Engineering, Xiamen University of Technology, Xiamen 361024, China.
Förderung
- Lili Ma
- Natural Science Foundation of Fujian Provincial of China
- Scientific Research Climbing Project of Xiamen University of Technology
Zitieren
APA
Zhao, Z., Jia, P., Zhang, Y., Ma, L., Sun, J., Xu, Y., & Wu, Y. (2024). Preparation of Ultrafine Co- and Ni-Coated (Ti,W,Mo,Ta)(C,N) Powders and Their Influence on the Microstructure of Ti(C,N)-Based Cermets. Materials, 17(8), 1807. https://doi.org/10.3390/ma17081807
Vancouver
Zhao Z, Jia P, Zhang Y, Ma L, Sun J, Xu Y, et al. Preparation of Ultrafine Co- and Ni-Coated (Ti,W,Mo,Ta)(C,N) Powders and Their Influence on the Microstructure of Ti(C,N)-Based Cermets. Materials. 2024;17(8):1807. doi:10.3390/ma17081807
BibTeX
@article{Zhao2024,
author = {Zhao, Zaiyang and Jia, Pengmin and Zhang, Yuhui and Ma, Lili and Sun, Jingjing and Xu, Yiping and Wu, Yurong},
title = {Preparation of Ultrafine Co- and Ni-Coated (Ti,W,Mo,Ta)(C,N) Powders and Their Influence on the Microstructure of Ti(C,N)-Based Cermets},
journal = {Materials},
year = {2024},
volume = {17},
number = {8},
pages = {1807},
doi = {10.3390/ma17081807}
}
EUVIMED