Effect of Cryogenic Treatments on Hardness, Fracture Toughness, and Wear Properties of Vanadis 6 Tool Steel
Materials · 07.04.2024 · 17 (7) · 1688
DOI: 10.3390/ma17071688 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 07.04.2024. Verfasst von Venu Yarasu und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Materials Technology Based in Trnava, Slovak University of Technology Based in Bratislava, 917 24 Trnava, Slovakia. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Scientific Grant Agency of the Ministry of Education, science, research and sport of the Slovak Republic and the Slovak Academy of Sciences, VEGA 1/0112/20.
Abstract (Originalsprache)
The ability of cryogenic treatment to improve tool steel performance is well established; however, the selection of optimal heat treatment is pivotal for cost reduction and extended tool life. This investigation delves into the influence of distinct cryogenic and tempering treatments on the hardness, fracture toughness, and tribological properties of Vanadis 6 tool steel. Emphasis was given to comprehending wear mechanisms, wear mode identification, volume loss estimation, and detailed characterization of worn surfaces through scanning electron microscopy coupled with energy dispersive spectroscopy and confocal microscopy. The findings reveal an 8–9% increase and a 3% decrease in hardness with cryogenic treatment compared to conventional treatment when tempered at 170 °C and 530 °C, respectively. Cryotreated specimens exhibit an average of 15% improved fracture toughness after tempering at 530 °C compared to conventional treatment. Notably, cryogenic treatment at −140 °C emerges as the optimum temperature for enhanced wear performance in both low- and high-temperature tempering scenarios. The identified wear mechanisms range from tribo-oxidative at lower contacting conditions to severe delaminative wear at intense contacting conditions. These results align with microstructural features, emphasizing the optimal combination of reduced retained austenite and the highest carbide population density observed in −140 °C cryogenically treated steel.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Materials Technology Based in Trnava, Slovak University of Technology Based in Bratislava, 917 24 Trnava, Slovakia.
- Institute of Physics of Materials, Czech Academy of Sciences, Zizkova 22, 616 62 Brno, Czech Republic.
- Department of Materials Engineering, Faculty of Mechanical Engineering, Czech Technical University, 160 00 Prague, Czech Republic.
ORCID-Profile: Peter Jurci, Jana Ptacinova, Ivo Dlouhy
Förderung
- Scientific Grant Agency of the Ministry of Education, science, research and sport of the Slovak Republic and the Slovak Academy of Sciences
- VEGA 1/0112/20
Zitieren
APA
Yarasu, V., Jurci, P., Ptacinova, J., Dlouhy, I., & Hornik, J. (2024). Effect of Cryogenic Treatments on Hardness, Fracture Toughness, and Wear Properties of Vanadis 6 Tool Steel. Materials, 17(7), 1688. https://doi.org/10.3390/ma17071688
Vancouver
Yarasu V, Jurci P, Ptacinova J, Dlouhy I, Hornik J. Effect of Cryogenic Treatments on Hardness, Fracture Toughness, and Wear Properties of Vanadis 6 Tool Steel. Materials. 2024;17(7):1688. doi:10.3390/ma17071688
BibTeX
@article{Yarasu2024,
author = {Yarasu, Venu and Jurci, Peter and Ptacinova, Jana and Dlouhy, Ivo and Hornik, Jakub},
title = {Effect of Cryogenic Treatments on Hardness, Fracture Toughness, and Wear Properties of Vanadis 6 Tool Steel},
journal = {Materials},
year = {2024},
volume = {17},
number = {7},
pages = {1688},
doi = {10.3390/ma17071688}
}
EUVIMED