EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting

Liaoyuan Wang, Yuli Sun, Zhongmin Xiao, Liming Yao iD, Jiale Guo, Shijie Kang, Weihao Mao, Dunwen Zuo

Materials · 27.03.2024 · 17 (7) · 1523

DOI: 10.3390/ma17071523 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.03.2024. Verfasst von Liaoyuan Wang und 7 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Interdisciplinary Innovation Fund for Doctoral Students of Nanjing University of Aeronautics and Astronautics, the China Scholarship Council, the State Key Laboratory of Robotics and Systems (HIT).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To enhance the surface quality of metal 3D-printed components, magnetic abrasive finishing (MAF) technology was employed for post-processing polishing. Experimental investigation employing response surface methodology was conducted to explore the impact of processing gap, rotational speed of the magnetic field, auxiliary vibration, and magnetic abrasive particle (MAP) size on the quality enhancement of internal surfaces. A regression model correlating roughness with crucial process parameters was established, followed by parameter optimization. Ultimately, the internal surface finishing of waveguides with blind cavities was achieved, and the finishing quality was comprehensively evaluated. Results indicate that under optimal process conditions, the roughness of the specimens decreased from Ra 2.5 μm to Ra 0.65 μm, reflecting a reduction rate of 74%. Following sequential rough and fine processing, the roughnesses of the cavity bottom, side wall, and convex surface inside the waveguide reduced to 0.59 μm, 0.61 μm, and 1.9 μm, respectively, from the original Ra above 12 μm. The findings of this study provide valuable technical insights into the surface finishing of metal 3D-printed components.

Schlagwörter

Stichwörter der Autor:innen

AlSi10Mg metal powdersmagnetic abrasive finishingselective laser meltingsurface roughness

Autor:innen und Institutionen

  • College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China.
  • School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore 639798, Singapore.
  • School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150080, China.
  • Zhengzhou Research Institute, Harbin Institute of Technology, Zhengzhou 450000, China.

ORCID-Profile: Liming Yao

Förderung

  • the Interdisciplinary Innovation Fund for Doctoral Students of Nanjing University of Aeronautics and Astronautics
  • the China Scholarship Council
  • the State Key Laboratory of Robotics and Systems (HIT)
  • International Scientific and Technological Cooperation project
  • Interdisciplinary Innovation Fund for Doctoral Students of Nanjing University of Aeronautics and Astronautics
  • China Scholarship Council
  • Graduate Innovative Experiment Competition Cultivation Project Fund of Nanjing University of Aeronautics and Astronautics
  • State Key Laboratory of Robotics and Systems (HIT)

Zitieren

APA

Wang, L., Sun, Y., Xiao, Z., Yao, L., Guo, J., Kang, S., Mao, W., & Zuo, D. (2024). Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting. Materials, 17(7), 1523. https://doi.org/10.3390/ma17071523

Vancouver

Wang L, Sun Y, Xiao Z, Yao L, Guo J, Kang S, et al. Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting. Materials. 2024;17(7):1523. doi:10.3390/ma17071523

BibTeX
@article{Wang2024,
  author = {Wang, Liaoyuan and Sun, Yuli and Xiao, Zhongmin and Yao, Liming and Guo, Jiale and Kang, Shijie and Mao, Weihao and Zuo, Dunwen},
  title = {Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {7},
  pages = {1523},
  doi = {10.3390/ma17071523}
}
Kostenlos starten →