EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Abrasive Wear Properties of Wear-Resistant Coating on Bucket Teeth Assessed Using a Dry Sand Rubber Wheel Tester

Zhongxin Wang, Long Sun, Dong Wang, Bo Song, Chang Liu, Zhenning Su, Chaobin Ma, Xiaoyong Ren iD

Materials · 26.03.2024 · 17 (7) · 1495

DOI: 10.3390/ma17071495 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 26.03.2024. Verfasst von Zhongxin Wang und 7 weiteren Autor:innen. Beteiligte Einrichtung: School of Mining, Liaoning Technical University, Fuxin 123000, China. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the National Key Research and Development Program of China, Science and Technology Innovation Venture Capital Special Foundation of China Coal Technology & Engineering Group, Shenyang Science and Technology Talent Special Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ni60-WC coatings with different WC contents on the bucket tooth substrates were pre- pared using laser cladding technology. Their abrasive wear properties were assessed using the dry sand rubber wheel test system. The substrate and the hard-facing layer were tested for comparison. The results showed that the hardness of the Ni60-WC coatings increased with the increase in WC content. The wear resistance of the bucket tooth substrate was greatly improved by hard-facing and laser cladding Ni60-WC coatings. The wear rate of the hard-facing layer was reduced to 1/6 of that of the tooth substrate. The wear rate of the laser cladding coatings with 20–40 wt.% WC was similar to that of the hard-facing layer. It is worth mentioning that the wear rate of the coatings with 60–80 wt.% WC was only 1/4 of that of the hard-facing layer. Micro-cutting with surface plastic deformation was the main wear mechanism of the substrate to form narrow and deep furrows. The wear mechanism of the hard-facing layer was mainly plastic deformation with a wide groove, and the surface cracks promoted the removal of the material. The removal of the binder phase caused by micro-cutting was the main wear mechanism of the laser cladding Ni60-WC coatings. However, the hard phase of WC hinders micro-cutting and plastic deformation, which improves the wear resistance of the coating.

Schlagwörter

Stichwörter der Autor:innen

abrasive wearbucket toothhard-facinglaser claddingwear mechanism

Autor:innen und Institutionen

  • School of Mining, Liaoning Technical University, Fuxin 123000, China.
  • Digital and Intelligent Industry Center, China Coal Technology Engineering Group (CCTEG), Shenyang Engineering Company, Shenyang 110013, China.
  • School of Mechanical and Electrical Engineering, China University of Mining and Technology-Beijing, Beijing 100083, China.

ORCID-Profile: Xiaoyong Ren

Förderung

  • the National Key Research and Development Program of China
  • Science and Technology Innovation Venture Capital Special Foundation of China Coal Technology & Engineering Group
  • Shenyang Science and Technology Talent Special Project
  • Science and Technology Innovation Venture Capital Special Foundation of China Coal Technology & Engineering Group

Zitieren

APA

Wang, Z., Sun, L., Wang, D., Song, B., Liu, C., Su, Z., Ma, C., & Ren, X. (2024). Abrasive Wear Properties of Wear-Resistant Coating on Bucket Teeth Assessed Using a Dry Sand Rubber Wheel Tester. Materials, 17(7), 1495. https://doi.org/10.3390/ma17071495

Vancouver

Wang Z, Sun L, Wang D, Song B, Liu C, Su Z, et al. Abrasive Wear Properties of Wear-Resistant Coating on Bucket Teeth Assessed Using a Dry Sand Rubber Wheel Tester. Materials. 2024;17(7):1495. doi:10.3390/ma17071495

BibTeX
@article{Wang2024,
  author = {Wang, Zhongxin and Sun, Long and Wang, Dong and Song, Bo and Liu, Chang and Su, Zhenning and Ma, Chaobin and Ren, Xiaoyong},
  title = {Abrasive Wear Properties of Wear-Resistant Coating on Bucket Teeth Assessed Using a Dry Sand Rubber Wheel Tester},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {7},
  pages = {1495},
  doi = {10.3390/ma17071495}
}
Kostenlos starten →