EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Manganese on the Strength–Toughness Relationship of Low-Carbon Copper and Nickel-Containing Hull Steel

Zhide Zhan, Zhongran Shi, Zemin Wang iD, Wenjing Lu, Zuoning Chen, Dian Zhang, Feng Chai, Xiaobing Luo

Materials · 22.02.2024 · 17 (5) · 1012

DOI: 10.3390/ma17051012 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 22.02.2024. Verfasst von Zhide Zhan und 7 weiteren Autor:innen. Beteiligte Einrichtung: School of Materials Science and Engineering, Shanghai Institute of Technology, 100 Haiquan Road, Shanghai 201418, China. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Central Iron and Steel Research Institute.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The influence of varying the manganese (Mn) contents of high-strength copper-containing hull steel on its microstructural evolution and mechanical properties was investigated. With increasing Mn content from 2 to 5%, the tensile strength of the steel increased by ~100 MPa, while the elongation of steel remained at ~23.5%, indicating good plasticity. However, the 2Mn sample had 128 J higher low-temperature (−84 °C) impact work than the 5Mn sample. The microstructures of different Mn steels were composed of fresh martensite (FM), ferrite/tempered martensite (F/TM), and reversed austenite (RA). The increase in Mn content markedly increased the presence of RA and intensified the work hardening caused by the transformation-induced plasticity (TRIP) effect during the tensile process. However, as the phase transformation in different Mn steels occurred in the early stage of strain and did not extend throughout the entire plastic deformation process, increasing plasticity via phase transformation was difficult. In addition, although the volume fraction of RA increased significantly in 4Mn and 5Mn steels, the stability of RA significantly decreased. The presence of numerous metastable blocks and coarse lath-like RA contributed little to low-temperature impact work and was even detrimental to toughness. The substantial fresh martensite resulting from phase transformation facilitated microcrack generation, owing to rapid volume expansion and mutual impacts, thus reducing the work required for crack formation. Additionally, the abundance of deformation twins significantly reduced the work needed for crack propagation. These combined actions significantly reduced the low-temperature toughness of 4Mn and 5Mn steels.

Schlagwörter

Stichwörter der Autor:innen

deformation twinmechanical propertiesreversed austenitetempering

Autor:innen und Institutionen

  • School of Materials Science and Engineering, Shanghai Institute of Technology, 100 Haiquan Road, Shanghai 201418, China.
  • Institute of Structural Steels, Central Iron and Steel Research Institute, Beijing 100081, China.
  • The State Key Laboratory of Refractories and M1, The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, China Metallurgy, Wuhan 430081, China.

ORCID-Profile: Zemin Wang

Förderung

  • Central Iron and Steel Research Institute

Zitieren

APA

Zhan, Z., Shi, Z., Wang, Z., Lu, W., Chen, Z., Zhang, D., Chai, F., & Luo, X. (2024). Effect of Manganese on the Strength–Toughness Relationship of Low-Carbon Copper and Nickel-Containing Hull Steel. Materials, 17(5), 1012. https://doi.org/10.3390/ma17051012

Vancouver

Zhan Z, Shi Z, Wang Z, Lu W, Chen Z, Zhang D, et al. Effect of Manganese on the Strength–Toughness Relationship of Low-Carbon Copper and Nickel-Containing Hull Steel. Materials. 2024;17(5):1012. doi:10.3390/ma17051012

BibTeX
@article{Zhan2024,
  author = {Zhan, Zhide and Shi, Zhongran and Wang, Zemin and Lu, Wenjing and Chen, Zuoning and Zhang, Dian and Chai, Feng and Luo, Xiaobing},
  title = {Effect of Manganese on the Strength–Toughness Relationship of Low-Carbon Copper and Nickel-Containing Hull Steel},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {5},
  pages = {1012},
  doi = {10.3390/ma17051012}
}
Kostenlos starten →