EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Research on the Hot Deformation Process of A100 Steel Based on High-Temperature Rheological Behavior and Microstructure

Chaoyuan Sun, Yi Qin, Yang Liu, Guiqian Xiao, Jiansheng Zhang iD, Jie Zhou

Materials · 21.02.2024 · 17 (5) · 991

DOI: 10.3390/ma17050991 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 21.02.2024. Verfasst von Chaoyuan Sun und 5 weiteren Autor:innen. Beteiligte Einrichtung: Chongqing Key Laboratory of Advanced Mold Intelligent Manufacturing, College of Materials Science and Engineering, Chongqing University, Chongqing 40…. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Chongqing Special Project for Technological Innovation and Application Development, Innovation Project of Taizhou S&T Support Program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To obtain the optimal hot deformation process, the rheological and dynamic recrystallization behaviors of A100 steel were researched through isothermal compression tests. Firstly, a Hensel-Spittel constitutive model was established based on the stress–strain curves. Secondly, dynamic recrystallization percentage and grain size models were established to identify the necessary conditions for complete dynamic recrystallization. Finally, microstructural analysis was employed to validate the accuracy of the recrystallization model. The results indicate that the flow stress is highly sensitive to both the strain rate and the temperature, and the HS model demonstrates a high predictive accuracy, with a correlation coefficient of 0.9914. There exists a contradictory relationship between decreasing the average grain size and increasing the recrystallization percentage. The higher the percentage of dynamic recrystallization, the larger the average grain size tends to be. This situation should be avoided when devising the actual processing procedures. The optimal hot working processes for achieving complete dynamic recrystallization and a smaller average grain size are as follows: a strain equal to or greater than 0.6, a temperature between 1193 and 1353 K, and a strain rate between 0.1 and 1 s−1.

Schlagwörter

Stichwörter der Autor:innen

constitutive modeldynamic recrystallizationgrain sizehot rheological behaviorhot working window

Autor:innen und Institutionen

  • Chongqing Key Laboratory of Advanced Mold Intelligent Manufacturing, College of Materials Science and Engineering, Chongqing University, Chongqing 400044, China.
  • China National Erzhong Group Deyang Wanhang Die Forging Co., Ltd., Deyang 618013, China.
  • Chongqing Jiepin Technology Co., Ltd., Chongqing 400000, China.

ORCID-Profile: Jiansheng Zhang

Förderung

  • National Natural Science Foundation of China
  • Chongqing Special Project for Technological Innovation and Application Development
  • Innovation Project of Taizhou S&T Support Program
  • Innovation Project of Taizhou S&T Support Program

Zitieren

APA

Sun, C., Qin, Y., Liu, Y., Xiao, G., Zhang, J., & Zhou, J. (2024). Research on the Hot Deformation Process of A100 Steel Based on High-Temperature Rheological Behavior and Microstructure. Materials, 17(5), 991. https://doi.org/10.3390/ma17050991

Vancouver

Sun C, Qin Y, Liu Y, Xiao G, Zhang J, Zhou J. Research on the Hot Deformation Process of A100 Steel Based on High-Temperature Rheological Behavior and Microstructure. Materials. 2024;17(5):991. doi:10.3390/ma17050991

BibTeX
@article{Sun2024,
  author = {Sun, Chaoyuan and Qin, Yi and Liu, Yang and Xiao, Guiqian and Zhang, Jiansheng and Zhou, Jie},
  title = {Research on the Hot Deformation Process of A100 Steel Based on High-Temperature Rheological Behavior and Microstructure},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {5},
  pages = {991},
  doi = {10.3390/ma17050991}
}
Kostenlos starten →