EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure and Properties of Aluminum–Graphene–SiC Matrix Composites after Friction Stir Processing

Chen Wang, Xianyong Zhu iD, Yuexiang Fan, Jiaan Liu, Liangwen Xie iD, Cheng Jiang, Xiong Xiao iD, Peng Wu, Xiangmi You

Materials · 20.02.2024 · 17 (5) · 979

DOI: 10.3390/ma17050979 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 20.02.2024. Verfasst von Chen Wang und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Aerospace Engineering, Jilin University, Changchun 130022, China. Die Arbeit wurde bisher 32-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science and Technology Development Projects of Changchun, Science and Technology Development Projects of Jilin Province, the Graduate Innovation Fund of Jilin University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Enhancing the mechanical properties of conventional ceramic particles-reinforced aluminum (Al 1060) metal matrix composites (AMCs) with lower detrimental phases is difficult. In this research work, AMCs are reinforced with graphene nanosheet (GNS) and hybrid reinforcement (GNS combined with 20% SiC, synthesized by shift-speed ball milling (SSBM), and further fabricated by two-pass friction stir processing (FSP). The effect of GNS content and the addition of SiC on the microstructure and mechanical properties of AMCs are studied. The microstructure, elemental, and phase composition of the developed composite are examined using SEM, EDS, and XRD techniques, respectively. Mechanical properties such as hardness, wear, and tensile strength are analyzed. The experimental results show that the GNS and the SiC are fairly distributed in the Al matrix via SSBM, which is beneficial for the mechanical properties of the composites. The maximum tensile strength of the composites is approximately 171.3 MPa in AMCs reinforced by hybrid reinforcements. The tensile strength of the GNS/Al composites increases when the GNS content increases from 0 to 1%, but then reduces with the further increase in GNS content. The hardness increases by 2.3%, 24.9%, 28.9%, and 41.8% when the Al 1060 is reinforced with 0.5, 1, 2% GNS, and a hybrid of SiC and GNS, respectively. The SiC provides further enhancement of the hardness of AMCs reinforced by GNS. The coefficient of friction decreases by about 7%, 13%, and 17% with the reinforcement of 0.5, 1, and 2% GNS, respectively. Hybrid reinforcement has the lowest friction coefficient (0.41). The decreasing friction coefficient contributes to the self-lubrication of GNSs, the reduction in the contact area with the substrate, and the load-bearing ability of ceramic particles. According to this study, the strengthening mechanisms of the composites may be due to thermal mismatch, grain refinement, and Orowan looping. In summary, such hybrid reinforcements effectively improve the mechanical and tribological properties of the composites.

Schlagwörter

Stichwörter der Autor:innen

aluminum matrix compositesfriction stir processinggraphene nanosheetsmicrostructuresilicon carbide

Autor:innen und Institutionen

  • School of Mechanical and Aerospace Engineering, Jilin University, Changchun 130022, China.
  • Chongqing Research Institute, Jilin University, Chongqing 401123, China.
  • College of Materials Science and Engineering, Jilin University, Changchun 130022, China.
  • Changchun Baoze Technology Co., Ltd., Changchun 130051, China.
  • CISDI Chongqing Iron & Steelmaking Plant Integration Co., Ltd., No.11 Huijin Road North New Zone, Chongqing 401122, China.

ORCID-Profile: Xianyong Zhu, Liangwen Xie, Xiong Xiao

Förderung

  • Science and Technology Development Projects of Changchun
  • Science and Technology Development Projects of Jilin Province
  • the Graduate Innovation Fund of Jilin University
  • Chongqing Research Institute of Jilin University Industrialization Technology Seed Pro-ject
  • Scientific research project of Jilin Provincial Department of Education in 2021
  • Technical Innovation and Application Development Special Project of Chongqing
  • Jilin University
  • Chongqing Research Institute of Jilin University Industrialization Technology Seed Project

Zitieren

APA

Wang, C., Zhu, X., Fan, Y., Liu, J., Xie, L., Jiang, C., Xiao, X., Wu, P., & You, X. (2024). Microstructure and Properties of Aluminum–Graphene–SiC Matrix Composites after Friction Stir Processing. Materials, 17(5), 979. https://doi.org/10.3390/ma17050979

Vancouver

Wang C, Zhu X, Fan Y, Liu J, Xie L, Jiang C, et al. Microstructure and Properties of Aluminum–Graphene–SiC Matrix Composites after Friction Stir Processing. Materials. 2024;17(5):979. doi:10.3390/ma17050979

BibTeX
@article{Wang2024,
  author = {Wang, Chen and Zhu, Xianyong and Fan, Yuexiang and Liu, Jiaan and Xie, Liangwen and Jiang, Cheng and Xiao, Xiong and Wu, Peng and You, Xiangmi},
  title = {Microstructure and Properties of Aluminum–Graphene–SiC Matrix Composites after Friction Stir Processing},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {5},
  pages = {979},
  doi = {10.3390/ma17050979}
}
Kostenlos starten →