EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure and Mechanical Behavior Comparison between Cast and Additive Friction Stir-Deposited High-Entropy Alloy Al0.35CoCrFeNi

Zackery McClelland, Kyle Dunsford, Brady Williams iD, Haley Petersen, Keivan Devami, Mark Weaver iD, J Brian Jordan, Paul G Allison iD

Materials · 16.02.2024 · 17 (4) · 910

DOI: 10.3390/ma17040910 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 16.02.2024. Verfasst von Zackery McClelland und 7 weiteren Autor:innen. Beteiligte Einrichtung: US Army Engineer Research and Development Center, Vicksburg, MS 39180, USA. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: U.S. Army Engineer Research and Development Center, U.S. Army ERDC, Director, Geotechnical and Structures Laboratory.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High-entropy alloys (HEAs) are new alloy systems that leverage solid solution strengthening to develop high-strength structural materials. However, HEAs are typically cast alloys, which may suffer from large as-cast grains and entrapped porosity, allowing for opportunities to further refine the microstructure in a non-melting near-net shape solid-state additive manufacturing process, additive friction stir deposition (AFSD). The present research compares the microstructure and mechanical behavior of the as-deposited AFSD Al0.35CoCrFeNi to the cast heat-treated properties to assess its viability for structural applications for the first time. Scanning electron microscopy (SEM) revealed the development of fine particles along the layer interfaces of the deposit. Quasi-static and intermediate-rate compression testing of the deposited material revealed a significant strain-rate sensitivity with a difference in yield strength of ~400 MPa. Overall, the AFSD process greatly reduced the grain size for the Al0.35CoCrFeNi alloy and approximately doubled the strength at both quasi-static and intermediate strain rates.

Schlagwörter

Stichwörter der Autor:innen

AlCoCrFeNi HEAadditive friction stir depositionmechanical propertymicrostructurestrength

Autor:innen und Institutionen

  • US Army Engineer Research and Development Center, Vicksburg, MS 39180, USA.
  • General Electric Aerospace, Cincinnati, OH 45215, USA.
  • Department of Mechanical Engineering, Baylor University, Waco, TX 76706, USA.
  • Department of Mechanical Engineering, Mississippi State University, Starkville, MS 39762, USA.
  • Department of Mechanical Engineering, The University of Alabama, Tuscaloosa, AL 35487, USA.
  • Department of Metallurgical Engineering, The University of Alabama, Tuscaloosa, AL 35487, USA.

ORCID-Profile: Brady Williams, Mark Weaver, Paul G Allison

Förderung

  • U.S. Army Engineer Research and Development Center
  • U.S. Army ERDC
  • Director, Geotechnical and Structures Laboratory

Zitieren

APA

McClelland, Z., Dunsford, K., Williams, B., Petersen, H., Devami, K., Weaver, M., Jordan, J. B., & Allison, P. G. (2024). Microstructure and Mechanical Behavior Comparison between Cast and Additive Friction Stir-Deposited High-Entropy Alloy Al0.35CoCrFeNi. Materials, 17(4), 910. https://doi.org/10.3390/ma17040910

Vancouver

McClelland Z, Dunsford K, Williams B, Petersen H, Devami K, Weaver M, et al. Microstructure and Mechanical Behavior Comparison between Cast and Additive Friction Stir-Deposited High-Entropy Alloy Al0.35CoCrFeNi. Materials. 2024;17(4):910. doi:10.3390/ma17040910

BibTeX
@article{McClelland2024,
  author = {McClelland, Zackery and Dunsford, Kyle and Williams, Brady and Petersen, Haley and Devami, Keivan and Weaver, Mark and Jordan, J Brian and Allison, Paul G},
  title = {Microstructure and Mechanical Behavior Comparison between Cast and Additive Friction Stir-Deposited High-Entropy Alloy Al0.35CoCrFeNi},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {4},
  pages = {910},
  doi = {10.3390/ma17040910}
}
Kostenlos starten →