EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Analysis of the Process and Results of High-Pressure Abrasive Water Jet Multilayer Cutting of Electrical Steel

Monika Szada-Borzyszkowska iD, Wojciech Kacalak, Łukasz Bohdal iD, Wiesław Szada-Borzyszkowski iD

Materials · 24.12.2023 · 17 (1) · 94

DOI: 10.3390/ma17010094 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.12.2023. Verfasst von Monika Szada-Borzyszkowska und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17 Street, 75-620 Koszalin, Poland. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Minister of Education and Science of the Republic of Poland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Electrical steels are magnetically soft materials and are widely used in the electrical industry for the construction of power transformer cores, distribution transformers, current transformers, and voltage transformers. An important parameter of electrical components, which determines the efficiency of devices, is energy loss during remagnetization. Energy losses are caused by eddy currents, hysteresis, and magnetic delay associated with the low quality of the cut edge after the cutting of steels, and material deformations and excessive stress concentration in the surrounding cutting zones. Common techniques for cutting electrical materials in industrial lines include mechanical cutting and laser cutting. Work has shown that mechanical cutting of electrical steel single layers results in the occurrence of large deformation zones, and in cutting processes with a high-pressure abrasive water jet (AWJ), significant uplifts of material and burrs at the bottom edges of sheets occur. The problem of increasing the cutting quality was solved through selecting the stream parameters for bundle cutting of electrical steels. It has been shown that in the process of cutting electrical sheet bundles, the height of burrs on the cut surface and the zone of plastic deformation are reduced. The work also presents comparison and analysis of characteristic features of the cut edge of electrical sheets obtained through high-pressure abrasive water jet and mechanical cutting processes. The influence of the type and processing parameters on the characteristic features of the material hysteresis loop was determined.

Schlagwörter

Stichwörter der Autor:innen

bundle cuttingcut surfaceelectrical steelelectrical steel single layershigh-pressure abrasive water jet cuttingmagnetic properties

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17 Street, 75-620 Koszalin, Poland.

ORCID-Profile: Monika Szada-Borzyszkowska, Łukasz Bohdal, Wiesław Szada-Borzyszkowski

Förderung

  • Minister of Education and Science of the Republic of Poland

Zitieren

APA

Szada-Borzyszkowska, M., Kacalak, W., Bohdal, Ł., & Szada-Borzyszkowski, W. (2023). Analysis of the Process and Results of High-Pressure Abrasive Water Jet Multilayer Cutting of Electrical Steel. Materials, 17(1), 94. https://doi.org/10.3390/ma17010094

Vancouver

Szada-Borzyszkowska M, Kacalak W, Bohdal Ł, Szada-Borzyszkowski W. Analysis of the Process and Results of High-Pressure Abrasive Water Jet Multilayer Cutting of Electrical Steel. Materials. 2023;17(1):94. doi:10.3390/ma17010094

BibTeX
@article{SzadaBorzyszkowska2023,
  author = {Szada-Borzyszkowska, Monika and Kacalak, Wojciech and Bohdal, Łukasz and Szada-Borzyszkowski, Wiesław},
  title = {Analysis of the Process and Results of High-Pressure Abrasive Water Jet Multilayer Cutting of Electrical Steel},
  journal = {Materials},
  year = {2023},
  volume = {17},
  number = {1},
  pages = {94},
  doi = {10.3390/ma17010094}
}
Kostenlos starten →