EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure, Mechanical and Corrosion Properties of Copper-Nickel 90/10 Alloy Produced by CMT-WAAM Method

Marcin Maleta, Joanna Kulasa, Aleksander Kowalski iD, Paweł Kwaśniewski iD, Sonia Boczkal, Marek Nowak

Materials · 22.12.2023 · 17 (1) · 50

DOI: 10.3390/ma17010050 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 22.12.2023. Verfasst von Marcin Maleta und 5 weiteren Autor:innen. Beteiligte Einrichtung: Łukasiewicz Research Network-Institute of Non-Ferrous Metals, ul. Sowińskiego 5, 44-100 Gliwice, Poland. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Education and Science of the Republic of Poland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the case of copper and its alloys, Wire Arc Additive Manufacturing (WAAM) 3D printing technology is mainly used to produce elements for the maritime industry and research has focused on the use of Cu-Al alloys. There is little information devoted to the use of Cu-Ni alloys in this technology, which are also widely used in the maritime industry. In this work, tests were carried out on the microstructure, mechanical properties, and corrosion properties in a 1M NaCl solution of Cu-Ni 90/10 alloy 3D walls printed using the WAAM method. The obtained objects are characterized by a microstructure with elongated column grains and particles of the Ni-Ti phase, hardness in the range of 138–160 HV10, ultimate tensile strength of 495–520 MPa, yield strength of 342–358 MPa, elongation of 16.6–17.9%, and a low average corrosion rate of 7.4 × 10−5 mm/year. The work shows that it is possible to obtain higher mechanical properties of Cu-Ni 90/10 alloy 3D objects produced using the WAAM method compared to cast materials, which opens up the possibility of using this alloy to produce objects with more complex shapes and for use in corrosive working conditions.

Schlagwörter

Stichwörter der Autor:innen

3D printingWAAMadditive manufacturingcopper-nickel alloycorrosion propertiesmechanical propertiesmicrostructure

Autor:innen und Institutionen

  • Łukasiewicz Research Network-Institute of Non-Ferrous Metals, ul. Sowińskiego 5, 44-100 Gliwice, Poland.
  • Faculty of Non-Ferrous Metals, AGH University of Science and Technology, al. Adama Mickiewicza 30, 30-059 Kraków, Poland.

ORCID-Profile: Aleksander Kowalski, Paweł Kwaśniewski

Förderung

  • Ministry of Education and Science of the Republic of Poland

Zitieren

APA

Maleta, M., Kulasa, J., Kowalski, A., Kwaśniewski, P., Boczkal, S., & Nowak, M. (2023). Microstructure, Mechanical and Corrosion Properties of Copper-Nickel 90/10 Alloy Produced by CMT-WAAM Method. Materials, 17(1), 50. https://doi.org/10.3390/ma17010050

Vancouver

Maleta M, Kulasa J, Kowalski A, Kwaśniewski P, Boczkal S, Nowak M. Microstructure, Mechanical and Corrosion Properties of Copper-Nickel 90/10 Alloy Produced by CMT-WAAM Method. Materials. 2023;17(1):50. doi:10.3390/ma17010050

BibTeX
@article{Maleta2023,
  author = {Maleta, Marcin and Kulasa, Joanna and Kowalski, Aleksander and Kwaśniewski, Paweł and Boczkal, Sonia and Nowak, Marek},
  title = {Microstructure, Mechanical and Corrosion Properties of Copper-Nickel 90/10 Alloy Produced by CMT-WAAM Method},
  journal = {Materials},
  year = {2023},
  volume = {17},
  number = {1},
  pages = {50},
  doi = {10.3390/ma17010050}
}
Kostenlos starten →