EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Annealing Heat Treatment for Homogenizing the Microstructure and Mechanical Properties of Electron-Beam-Welded Thick Plate of Ti-6Al-4V Alloy

Seongji Seo iD, Jiyong Park iD

Materials · 29.11.2023 · 16 (23) · 7423

DOI: 10.3390/ma16237423 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 29.11.2023. Verfasst von Seongji Seo und 1 weiteren Autor:innen. Beteiligte Einrichtung: Advanced Joining & Additivie Manufacturing R&D Department, Korea Institute of Industrial Technology, Incheon 21999, Republic of Korea. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Korea Institute of Industrial Technology, Ministry of Trade, Industry and Energy.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the application of Ti-6Al-4V to aerospace structural components, when welding thick plates similar of the thickness of the components, microstructure and hardness gradients emerge between the base material (BM) and the joint. This leads to the issue of significant stress concentration in the BM under tensile stress. To address this problem through post-welding heat treatment, this study conducted heat treatments at temperatures both below (mill annealing, MA) and above the beta-transus temperature (beta annealing, BA) on electron-beam weldments of 18 mm thickness Ti-6Al-4V plates. Subsequently, microstructures and hardness were analyzed at different depths from the upper surface and areas (fusion zone (FZ), heat-affected zone (HAZ), and BM), and tensile properties were measured at various depths. The results indicated that α′ observed in FZ and HAZ was resolved through both MA and BA. Particularly after BA, the microstructural gradient that persisted even after MA completely disappeared, resulting in the homogenization of widmanstätten α + β. Consequently, after BA, the hardness gradient in each zone also disappeared, and the tensile strength was higher than in just-welded and MA heat-treated plates.

Schlagwörter

Stichwörter der Autor:innen

Ti-6Al-4V alloybeta annealingelectron beam weldingmechanical propertiesmicrostructuremill annealing

Autor:innen und Institutionen

  • Advanced Joining & Additivie Manufacturing R&D Department, Korea Institute of Industrial Technology, Incheon 21999, Republic of Korea.
  • Department of Materials Science and Enginering, Hanyang University, Seoul 04763, Republic of Korea.
  • Department of Convergence Manufacturing System Engineering, Korea National University of Science and Technology, Daejeon 34113, Republic of Korea.

ORCID-Profile: Seongji Seo, Jiyong Park

Förderung

  • Korea Institute of Industrial Technology
  • Ministry of Trade, Industry and Energy

Zitieren

APA

Seo, S., & Park, J. (2023). Annealing Heat Treatment for Homogenizing the Microstructure and Mechanical Properties of Electron-Beam-Welded Thick Plate of Ti-6Al-4V Alloy. Materials, 16(23), 7423. https://doi.org/10.3390/ma16237423

Vancouver

Seo S, Park J. Annealing Heat Treatment for Homogenizing the Microstructure and Mechanical Properties of Electron-Beam-Welded Thick Plate of Ti-6Al-4V Alloy. Materials. 2023;16(23):7423. doi:10.3390/ma16237423

BibTeX
@article{Seo2023,
  author = {Seo, Seongji and Park, Jiyong},
  title = {Annealing Heat Treatment for Homogenizing the Microstructure and Mechanical Properties of Electron-Beam-Welded Thick Plate of Ti-6Al-4V Alloy},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {23},
  pages = {7423},
  doi = {10.3390/ma16237423}
}
Kostenlos starten →