EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Pulsed Arc Parameters on the Tig Welding Process for the Stainless Steel Duplex UNS S31803

Vinicius Marques Alves Generoso, Lucas Menezes de Souza, Elaine Cristina Pereira, Sergio N Monteiro iD, Afonso R G de Azevedo iD

Materials · 26.10.2023 · 16 (21) · 6870

DOI: 10.3390/ma16216870 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 26.10.2023. Verfasst von Vinicius Marques Alves Generoso und 4 weiteren Autor:innen. Beteiligte Einrichtung: UENF-State University of the Northern Rio de Janeiro, LAMAV-Advanced Materials Laboratory, Av. Alberto Lamego, 2000, Campos dos Goytacazes 28013-602,…. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: State University of the Northern Fluminense (UENF), CAPES, CNPq.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The influence of parameters involved in the pulsed electric arc, used as an energy source in the tungsten inert gas (TIG)-mediated welding of Duplex UNS S31803 stainless steel, to attend the manufacture of flexible pipes for the extraction of oil and gas is presented. A fundamental part in the manufacturing process of flexible pipelines is the welding of these strips so that corresponding TIG welds will be subjected to the same process and work conditions. Therefore, it is necessary to maintain the same properties in the welded regions. Covering the effects of each parameter of the pulsed electric arc such as peak and base current as welds, cyclic ratio, and pulsation frequency is a desirable endeavor. The final objective is the mitigation of problems that have a great impact on production, such as weld breakage during the conformation of the strip in the process and test failures. With this, tensile, bending, and ferrite percentage tests were performed on 12 samples that qualified as satisfactory in the visual aspect. A minimum tensile strength of 734.57 MPa and a maximum of 775.77 MPa were obtained where all values found are above the tensile strength limit of the base material of 620 MPa. With the completion of the study, it is possible to understand not only the response of the process to each parameter but also the tendency when changing them. Moreover, it is possible to explore the possibility of guiding the changes to achieve results about the visual aspect and the mechanical properties of the welded material.

Schlagwörter

Stichwörter der Autor:innen

cyclic ratiomicrostructurepost weld heat treatmentpulsation frequencystainless duplex steel

Autor:innen und Institutionen

  • UENF-State University of the Northern Rio de Janeiro, LAMAV-Advanced Materials Laboratory, Av. Alberto Lamego, 2000, Campos dos Goytacazes 28013-602, RJ, Brazil.
  • IME-Military Institute of Engineering, Materials Science Program, Praça General Tibúrcio, 80, Urca, Rio de Janeiro 22290-270, RJ, Brazil.
  • UENF-State University of the Northern Rio de Janeiro, LECIV-Civil Engineering Laboratory, Av. Alberto Lamego, 2000, Campos dos Goytacazes 28013-602, RJ, Brazil.

ORCID-Profile: Sergio N Monteiro, Afonso R G de Azevedo

Förderung

  • State University of the Northern Fluminense (UENF)
  • CAPES
  • CNPq
  • FAPERJ

Zitieren

APA

Generoso, V. M. A., Souza, L. M., Pereira, E. C., Monteiro, S. N., & de Azevedo, A. R. G. (2023). Influence of Pulsed Arc Parameters on the Tig Welding Process for the Stainless Steel Duplex UNS S31803. Materials, 16(21), 6870. https://doi.org/10.3390/ma16216870

Vancouver

Generoso VMA, Souza LM, Pereira EC, Monteiro SN, de Azevedo ARG. Influence of Pulsed Arc Parameters on the Tig Welding Process for the Stainless Steel Duplex UNS S31803. Materials. 2023;16(21):6870. doi:10.3390/ma16216870

BibTeX
@article{Generoso2023,
  author = {Generoso, Vinicius Marques Alves and Souza, Lucas Menezes de and Pereira, Elaine Cristina and Monteiro, Sergio N and de Azevedo, Afonso R G},
  title = {Influence of Pulsed Arc Parameters on the Tig Welding Process for the Stainless Steel Duplex UNS S31803},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {21},
  pages = {6870},
  doi = {10.3390/ma16216870}
}
Kostenlos starten →