EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

In Situ, Real-Time Temperature Mapping and Thermal FE Simulations of Large-Format 3D Printed PETG/CF Vertical Wall

Felipe Robles Poblete, Matthew Ireland iD, Lucinda Slattery iD, William G Davids iD, Roberto A Lopez-Anido iD

Materials · 29.09.2023 · 16 (19) · 6486

DOI: 10.3390/ma16196486 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 29.09.2023. Verfasst von Felipe Robles Poblete und 4 weiteren Autor:innen. Beteiligte Einrichtung: Advanced Structures and Composites Center (ASCC), University of Maine, Orono, ME 04469, USA. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 74 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Engineer Research and Development Center, U.S. Army Engineer Research and Development Center (ERDC), Russell S. Bodwell University Distinguished Professorship.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work focuses on simulating the thermal history of a vertical wall consisting of a thermoplastic composite material, poly(ethylene terephthalate) glycol (PETG) with short carbon fiber reinforcement, manufactured using a Big Area Additive Manufacturing (BAAM) system. The incremental deposition process used in additive manufacturing, which corresponds to the repeated deposition of hot material onto cooler material, contributes to the presence of residual stresses and part warping. The prediction of these mechanisms is dependent on thermal history of the part, and the major motivation of this work was to improve the accuracy of finite element (FE) models used to quantify the thermal history of large-format additively manufactured parts. Thermocouples were placed throughout the part at varying heights to measure temperature as a function of time. The FE model developed found a thermal contact conductance between the printed part and the bed of 10 W/m2K and convection coefficient values that linearly varied from 3 to 15 W/m2K through the wall height when making a temperature comparison with the output from the thermocouples. It is also demonstrated that the FE model with a constant convection coefficient under-predicts model temperature at the beginning of the manufacturing process when compared against the model with a variable convection coefficient. The impact of this difference was seen in the stress values, which were larger for the model with a constant convection coefficient. Finally, a correlation equation was derived which allows the findings to be generalized to other vertical structures manufactured on the BAAM. In summary, this work offers valuable insights on material characterization, real-time thermocouple placement, and FE modeling of large-format additively manufactured parts.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingconductanceconvectionfinite elementmodelingpolymerthermoplastic

Autor:innen und Institutionen

  • Advanced Structures and Composites Center (ASCC), University of Maine, Orono, ME 04469, USA.
  • Department of Physics and Astronomy, University of Maine, Orono, ME 04469, USA.
  • Department of Civil and Environmental Engineering, University of Maine, Orono, ME 04469, USA.

ORCID-Profile: Matthew Ireland, Lucinda Slattery, William G Davids, Roberto A Lopez-Anido

Förderung

  • Engineer Research and Development Center
  • U.S. Army Engineer Research and Development Center (ERDC)
  • Russell S. Bodwell University Distinguished Professorship
  • Malcolm G. Long ‘32 Professorship in Civil Engineering

Zitieren

APA

Robles Poblete, F., Ireland, M., Slattery, L., Davids, W. G., & Lopez-Anido, R. A. (2023). In Situ, Real-Time Temperature Mapping and Thermal FE Simulations of Large-Format 3D Printed PETG/CF Vertical Wall. Materials, 16(19), 6486. https://doi.org/10.3390/ma16196486

Vancouver

Robles Poblete F, Ireland M, Slattery L, Davids WG, Lopez-Anido RA. In Situ, Real-Time Temperature Mapping and Thermal FE Simulations of Large-Format 3D Printed PETG/CF Vertical Wall. Materials. 2023;16(19):6486. doi:10.3390/ma16196486

BibTeX
@article{RoblesPoblete2023,
  author = {Robles Poblete, Felipe and Ireland, Matthew and Slattery, Lucinda and Davids, William G and Lopez-Anido, Roberto A},
  title = {In Situ, Real-Time Temperature Mapping and Thermal FE Simulations of Large-Format 3D Printed PETG/CF Vertical Wall},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {19},
  pages = {6486},
  doi = {10.3390/ma16196486}
}
Kostenlos starten →