Stress Relieving Heat Treatment of 316L Stainless Steel Made by Additive Manufacturing Process
Materials · 28.09.2023 · 16 (19) · 6461
DOI: 10.3390/ma16196461 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 28.09.2023. Verfasst von Matúš Gel'atko und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Manufacturing Technologies, Technical University of Košice, 080 01 Prešov, Slovakia. Die Arbeit wurde bisher 41-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovak Research and Development Agency, Ministry of Education, Science, Research and Sport of the Slovak Republic, European Regional Development Fund.
Abstract (Originalsprache)
Residual stress occurs in the materials after different methods of processing due to the application of pressure and/or thermal gradient. The occurrence of residual stresses can be observed in both subtractive and additive-manufactured (AM) materials and objects. However, pressure residual stresses are considered, in some cases, to have a positive effect; there are applications where the neutral stress state is required. As there is a lack of standards describing the heat treatment of AM materials, there is a need for experimental research in this field. The objective of this article is to determine the heat treatment thermal regime to achieve close to zero stress state in the subsurface layer of additively manufactured AM316L stainless steel. The presented objective leads to the long-term goal of neutral etalons for eddy current residual stress testing preparation. A semi-product intended for the experiment was prepared using the Selective Laser Melting (SLM) process and subsequently cut, using Abrasive Water Jet (AWJ) technology, into experimental specimens, which were consequently heat-treated in combination with four temperatures and three holding times. Residual stresses were measured using X-ray diffraction (XRD), and microstructure variations were observed and examined. A combination of higher temperature and longer duration of heat treatment caused more significant stress relaxation, and the original stress state of the material influenced a degree of this relaxation. The microstructure formed of cellular grains changed slightly in the form of grain growth with randomly occurring unmolten powder particles, porosity, and inclusion precipitation.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Manufacturing Technologies, Technical University of Košice, 080 01 Prešov, Slovakia.
- Center of 3D Printing Protolab, Department of Machining, Assembly and Engineering Technology, Faculty of Mechanical Engineering, VSB-TU Ostrava, 17. Listopadu 2172/15, 708 00 Ostrava, Czech Republic.
- Department of Machining and Manufacturing Technology, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 1, 010 26 Žilina, Slovakia.
ORCID-Profile: Matúš Gel'atko, Michal Hatala, František Botko, Radoslav Vandžura, Jiří Hajnyš, Michal Šajgalík, Jozef Török
Förderung
- Slovak Research and Development Agency
- Ministry of Education, Science, Research and Sport of the Slovak Republic
- European Regional Development Fund
- Ministry of Education, Science, Research, and Sport of the Slovak Republic
- ERDF
Zitieren
APA
Gel'atko, M., Hatala, M., Botko, F., Vandžura, R., Hajnyš, J., Šajgalík, M., & Török, J. (2023). Stress Relieving Heat Treatment of 316L Stainless Steel Made by Additive Manufacturing Process. Materials, 16(19), 6461. https://doi.org/10.3390/ma16196461
Vancouver
Gel'atko M, Hatala M, Botko F, Vandžura R, Hajnyš J, Šajgalík M, et al. Stress Relieving Heat Treatment of 316L Stainless Steel Made by Additive Manufacturing Process. Materials. 2023;16(19):6461. doi:10.3390/ma16196461
BibTeX
@article{Gelatko2023,
author = {Gel'atko, Matúš and Hatala, Michal and Botko, František and Vandžura, Radoslav and Hajnyš, Jiří and Šajgalík, Michal and Török, Jozef},
title = {Stress Relieving Heat Treatment of 316L Stainless Steel Made by Additive Manufacturing Process},
journal = {Materials},
year = {2023},
volume = {16},
number = {19},
pages = {6461},
doi = {10.3390/ma16196461}
}
EUVIMED