EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure and Strength of Ti-6Al-4V Samples Additively Manufactured with TiC Heterogeneous Nucleation Site Particles

Yoshimi Watanabe iD, Shintaro Yamada, Tadachika Chiba, Hisashi Sato iD, Seiji Miura iD, Kenshiro Abe, Tomotsugu Kato

Materials · 31.08.2023 · 16 (17) · 5974

DOI: 10.3390/ma16175974 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 31.08.2023. Verfasst von Yoshimi Watanabe und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Physical Science and Engineering, Nagoya Institute of Technology, Nagoya 466-8555, Japan. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Light Metal Educational Foundation of Japan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Our research aims to investigate the fabrication of additively manufactured (AMed) Ti-6Al-4V samples under reduced power with the addition of TiC heterogeneous nucleation site particles. For this aim, Ti-6Al-4V samples are fabricated with and without TiC heterogeneous nucleation site particles using an EOS M 290 machine under optimal parameters and reduced power conditions. The microstructure and tensile behavior of the produced samples were studied. In addition, a single-track test was performed to obtain a good understanding of the suppression of gas pores and balling formation with the addition of TiC heterogeneous nucleation site particles. It was found that the formation of gas pores and balling was suppressed with the addition of heterogeneous nucleation site particles within the metallic powder.

Schlagwörter

Stichwörter der Autor:innen

Ti-6Al-4V alloyadditive manufacturingheterogeneous nucleation site particleslattice matchingpowder bed fusion (PBF)single track testtensile test

Autor:innen und Institutionen

  • Department of Physical Science and Engineering, Nagoya Institute of Technology, Nagoya 466-8555, Japan.
  • Division of Materials Science and Engineering, Hokkaido University, Sapporo 060-8628, Japan.
  • Nabtesco Corporation, Tokyo 102-0093, Japan.

ORCID-Profile: Yoshimi Watanabe, Hisashi Sato, Seiji Miura

Förderung

  • Light Metal Educational Foundation of Japan

Zitieren

APA

Watanabe, Y., Yamada, S., Chiba, T., Sato, H., Miura, S., Abe, K., & Kato, T. (2023). Microstructure and Strength of Ti-6Al-4V Samples Additively Manufactured with TiC Heterogeneous Nucleation Site Particles. Materials, 16(17), 5974. https://doi.org/10.3390/ma16175974

Vancouver

Watanabe Y, Yamada S, Chiba T, Sato H, Miura S, Abe K, et al. Microstructure and Strength of Ti-6Al-4V Samples Additively Manufactured with TiC Heterogeneous Nucleation Site Particles. Materials. 2023;16(17):5974. doi:10.3390/ma16175974

BibTeX
@article{Watanabe2023,
  author = {Watanabe, Yoshimi and Yamada, Shintaro and Chiba, Tadachika and Sato, Hisashi and Miura, Seiji and Abe, Kenshiro and Kato, Tomotsugu},
  title = {Microstructure and Strength of Ti-6Al-4V Samples Additively Manufactured with TiC Heterogeneous Nucleation Site Particles},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {17},
  pages = {5974},
  doi = {10.3390/ma16175974}
}
Kostenlos starten →