EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development and Fabrication of Biocompatible Ti-Based Bulk Metallic Glass Matrix Composites for Additive Manufacturing

Po-Sung Chen, Pei-Hua Tsai, Tsung-Hsiung Li, Jason Shian-Ching Jang iD, Jacob Chih-Ching Huang iD, Che-Hsin Lin iD, Cheng-Tang Pan, Hsuan-Kai Lin iD

Materials · 30.08.2023 · 16 (17) · 5935

DOI: 10.3390/ma16175935 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 30.08.2023. Verfasst von Po-Sung Chen und 7 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Materials Science and Engineering, National Central University, Taoyuan 32001, Taiwan. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Technology of Taiwan, Ministry of Science and Technology of Taiwan, Republic of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ti-based metallic glasses have a high potential for implant applications. The feasibility of a new biocompatible Ti-based bulk metallic glass composite for selective laser melting (SLM) had been examined. Therefore, it is necessary to design a high-glass-forming-ability Ti-based metallic glass (∆Tx = 81 K, γ = 0.427, γm = 0.763), to fabricate a partial glass-formable spherical powder (the volume fraction of the amorphous phase in the atomized Ti-based powders being 73% [size < 25 μm], 61% [25–37 μm], and 50% [37–44 μm]), and establish an SLM parameter (a scan rate of 600 mm/s, a power of 120 W, and an overlap of 10%). The Ti42Zr35Si5Co12.5Sn2.5Ta3 bulk metallic glass composite was successfully fabricated through SLM. This study demonstrates that the TiZrSiCoSnTa system constitutes a promising basis for the additive manufacturing process in terms of preparing biocompatible metallic glass composites into complicated graded foam shapes.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturing (AM)biocompatiblemetallic glass (MG)selective laser melting (SLM)

Autor:innen und Institutionen

  • Institute of Materials Science and Engineering, National Central University, Taoyuan 32001, Taiwan.
  • Department of Mechanical Engineering, National Central University, Taoyuan 32001, Taiwan.
  • Department of Materials and Optoelectronic Materials, National Sun Yat-Sen University, Kaohsiung 80424, Taiwan.
  • Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University, Kaohsiung 80424, Taiwan.
  • Department of Materials Engineering, National Pingtung University of Science and Technology, Pingtung 91201, Taiwan.

ORCID-Profile: Jason Shian-Ching Jang, Jacob Chih-Ching Huang, Che-Hsin Lin, Hsuan-Kai Lin

Förderung

  • Ministry of Science and Technology of Taiwan
  • Ministry of Science and Technology of Taiwan, Republic of China

Zitieren

APA

Chen, P. S., Tsai, P. H., Li, T. H., Jang, J. S., Huang, J. C., Lin, C. H., Pan, C. T., & Lin, H. K. (2023). Development and Fabrication of Biocompatible Ti-Based Bulk Metallic Glass Matrix Composites for Additive Manufacturing. Materials, 16(17), 5935. https://doi.org/10.3390/ma16175935

Vancouver

Chen PS, Tsai PH, Li TH, Jang JS, Huang JC, Lin CH, et al. Development and Fabrication of Biocompatible Ti-Based Bulk Metallic Glass Matrix Composites for Additive Manufacturing. Materials. 2023;16(17):5935. doi:10.3390/ma16175935

BibTeX
@article{Chen2023,
  author = {Chen, Po-Sung and Tsai, Pei-Hua and Li, Tsung-Hsiung and Jang, Jason Shian-Ching and Huang, Jacob Chih-Ching and Lin, Che-Hsin and Pan, Cheng-Tang and Lin, Hsuan-Kai},
  title = {Development and Fabrication of Biocompatible Ti-Based Bulk Metallic Glass Matrix Composites for Additive Manufacturing},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {17},
  pages = {5935},
  doi = {10.3390/ma16175935}
}
Kostenlos starten →