EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fabrication of Multi-Walled Structure through Parametric Study of Bead Geometries of GMAW-Based WAAM Process of SS309L

Jay Vora iD, Rudram Pandey iD, Pratik Dodiya, Vivek Patel iD, Sakshum Khanna iD, Vatsal Vaghasia, Rakesh Chaudhari iD

Materials · 21.07.2023 · 16 (14) · 5147

DOI: 10.3390/ma16145147 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 21.07.2023. Verfasst von Jay Vora und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, School of Technology, Pandit Deendayal Energy University, Raisan, Gandhinagar 382007, India. Die Arbeit wurde bisher 41-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Institution of Engineers (India).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the present study, an attempt is made to investigate and optimize the bead geometries of bead width (BW) and bead height (BH) of SS-309L using an SS316L substrate by employing a gas metal arc welding (GMAW)-based wire-arc additive manufacturing (WAAM) process. The Box–Behnken design approach was used to conduct the trials of single-layer depositions with input variables of travel speed (TS), voltage (V), and gas mixture ratio (GMR). The developed multi-variable regression models were tested for feasibility using ANOVA and residual plots. The data obtained indicated that V had the most significant impact on BW, followed by TS and GMR. For BH, TS had the most significant impact, followed by GMR and V. The results of single-response optimization using a passing vehicle search (PVS) algorithm showed a maximum BH of 9.48 mm and a minimum BW of 5.90 mm. To tackle the contradictory situation, a multi-objective PVS algorithm was employed, which produced non-dominated solutions. A multi-layered structure was successfully fabricated at the optimal parametric settings of TS at 20 mm/s, of voltage at 22 V, and of GMR at 3. For multi-layer structures, fusion among the layers was observed to be good, and they were found to be free from the disbonding of layers. This revealed the suitability of the PVS algorithm for generating suitable optimal WAAM variables. We consider the current work highly beneficial for users fabricating multi-layer structures.

Schlagwörter

Stichwörter der Autor:innen

Gas Metal Arc Welding (GMAW)SS309LLWire-Arc Additive Manufacturing (WAAM)bead geometriesmulti-walled structurepassing vehicle search (PVS) optimization

Autor:innen und Institutionen

  • Department of Mechanical Engineering, School of Technology, Pandit Deendayal Energy University, Raisan, Gandhinagar 382007, India.
  • Journal of Visualized Experiments, Delhi 110016, India.

ORCID-Profile: Jay Vora, Rudram Pandey, Vivek Patel, Sakshum Khanna, Rakesh Chaudhari

Förderung

  • Institution of Engineers (India)

Zitieren

APA

Vora, J., Pandey, R., Dodiya, P., Patel, V., Khanna, S., Vaghasia, V., & Chaudhari, R. (2023). Fabrication of Multi-Walled Structure through Parametric Study of Bead Geometries of GMAW-Based WAAM Process of SS309L. Materials, 16(14), 5147. https://doi.org/10.3390/ma16145147

Vancouver

Vora J, Pandey R, Dodiya P, Patel V, Khanna S, Vaghasia V, et al. Fabrication of Multi-Walled Structure through Parametric Study of Bead Geometries of GMAW-Based WAAM Process of SS309L. Materials. 2023;16(14):5147. doi:10.3390/ma16145147

BibTeX
@article{Vora2023,
  author = {Vora, Jay and Pandey, Rudram and Dodiya, Pratik and Patel, Vivek and Khanna, Sakshum and Vaghasia, Vatsal and Chaudhari, Rakesh},
  title = {Fabrication of Multi-Walled Structure through Parametric Study of Bead Geometries of GMAW-Based WAAM Process of SS309L},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {14},
  pages = {5147},
  doi = {10.3390/ma16145147}
}
Kostenlos starten →