EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Characterization of Composite-Printed Materials for the Production of Multirotor UAV Airframe Parts

Tomislav Šančić, Marino Brčić iD, Denis Kotarski iD, Andrzej Łukaszewicz iD

Materials · 18.07.2023 · 16 (14) · 5060

DOI: 10.3390/ma16145060 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.07.2023. Verfasst von Tomislav Šančić und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Karlovac University of Applied Sciences, 47000 Karlovac, Croatia. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Regional Development Fund. Operational programme competitiveness and cohesion 2014-2020, European Regional Development Fund.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this paper, the characterization of 3D-printed materials that are considered in the design of multirotor unmanned aerial vehicles (UAVs) for specialized purposes was carried out. The multirotor UAV system is briefly described, primarily from the aspect of system dynamics, considering that the airframe parts connect the UAV components, including the propulsion configuration, into a functional assembly. Three additive manufacturing (AM) technologies were discussed, and a brief overview was provided of selective laser sintering (SLS), fused deposition modeling (FDM), and continuous fiber fabrication (CFF). Using hardware and related software, 12 series of specimens were produced, which were experimentally tested utilizing a quasi-static uniaxial tensile test. The results of the experimental tests are provided graphically with stress–strain diagrams. In this work, the focus is on CFF technology and the testing of materials that will be used in the production of mechanically loaded airframe parts of multirotor UAVs. The experimentally obtained values of the maximum stresses were compared for different technologies. For the considered specimens manufactured using FDM and SLS technology, the values are up to 40 MPa, while for the considered CFF materials and range of investigated specimens, it is shown that it can be at least four times higher. By increasing the proportion of fibers, these differences increase. To be able to provide a wider comparison of CFF technology and investigated materials with aluminum alloys, the following three-point flexural and Charpy impact tests were selected that fit within this framework for experimental characterization.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingcontinuous fiber fabricationfiberglass reinforcementmaterial experimental characterizationmultirotor UAV airframe partsuniaxial tensile test

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Karlovac University of Applied Sciences, 47000 Karlovac, Croatia.
  • Department of Engineering Mechanics, Faculty of Engineering, University of Rijeka, 51000 Rijeka, Croatia.
  • Institute of Mechanical Engineering, Faculty of Mechanical Engineering, Bialystok University of Technology, 15-351 Bialystok, Poland.

ORCID-Profile: Marino Brčić, Denis Kotarski, Andrzej Łukaszewicz

Förderung

  • European Regional Development Fund. Operational programme competitiveness and cohesion 2014-2020
  • European Regional Development Fund

Zitieren

APA

Šančić, T., Brčić, M., Kotarski, D., & Łukaszewicz, A. (2023). Experimental Characterization of Composite-Printed Materials for the Production of Multirotor UAV Airframe Parts. Materials, 16(14), 5060. https://doi.org/10.3390/ma16145060

Vancouver

Šančić T, Brčić M, Kotarski D, Łukaszewicz A. Experimental Characterization of Composite-Printed Materials for the Production of Multirotor UAV Airframe Parts. Materials. 2023;16(14):5060. doi:10.3390/ma16145060

BibTeX
@article{ani2023,
  author = {Šančić, Tomislav and Brčić, Marino and Kotarski, Denis and Łukaszewicz, Andrzej},
  title = {Experimental Characterization of Composite-Printed Materials for the Production of Multirotor UAV Airframe Parts},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {14},
  pages = {5060},
  doi = {10.3390/ma16145060}
}
Kostenlos starten →