EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Evaluation of Mechanical Properties and Filler Interaction in the Field of SLA Polymeric Additive Manufacturing

Petr Jirků, Jiří Urban, Miroslav Müller iD, Viktor Kolář iD, Vijay Chandan, Jaroslava Svobodová iD, Rajesh Kumar Mishra iD, Hafsa Jamshaid iD

Materials · 12.07.2023 · 16 (14) · 4955

DOI: 10.3390/ma16144955 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 12.07.2023. Verfasst von Petr Jirků und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences Prague, Kamycka 129, 165 00 Pr…. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague grants no. 2022:31140/1312/3105: "Research on composite materials wit…, Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague grants no. 2023:31140/1312/3104: "Development and testing of polymer…, Internal Grant Agency of the Faculty of Engineering, Czech University of Life Sciences Prague.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The paper deals with research focused on the use of fillers in the field of polymeric materials produced by additive technology SLA (stereolithography). The aim of the research is to evaluate 3D printing parameters, the mechanical properties (tensile strength, hardness), and the interaction of individual phases (polymer matrix and filler) in composite materials using SEM analysis. The tested fillers were cotton flakes and ground carbon fibres in different proportions. For the photosensitive resins, the use of cotton flakes as filler was found to have a positive effect on the mechanical properties not only under static but also under cyclic loading, which is a common cause of material failure in practice. The cyclic stress reference value was set at an amplitude of 5–50% of the maximum force required to break the pure resin in a static tensile test. A positive effect of fillers on the cyclic stress life of materials was demonstrated. The service life of pure resin was only 168 ± 29 cycles. The service life of materials with fillers increased to approximately 400 to 540 cycles for carbon fibre-based fillers and nearly 1000 cycles for cotton flake-based fillers, respectively. In this paper, new composite materials suitable for the use of SLA additive manufacturing techniques are presented. Research demonstrated the possibilities of adding cotton-based fillers in low-cost, commercially available resins. Furthermore, the importance of material research under cyclic loading was demonstrated.

Schlagwörter

Stichwörter der Autor:innen

3D printingcarbon fillercotton fillercyclic loadinglow cycle testpolymer composite

Autor:innen und Institutionen

  • Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences Prague, Kamycka 129, 165 00 Prague, Czech Republic.
  • Faculty of Mechanical Engineering, University of Jan Evangelista Purkyně in Ústí nad Labem (UJEP), Pasteurova 3334/7, 400 01 Usti nad Labem, Czech Republic.
  • Faculty of Textile Engineering, National Textile University, Sheikhupura Road, Faisalabad 37610, Pakistan.

ORCID-Profile: Miroslav Müller, Viktor Kolář, Jaroslava Svobodová, Rajesh Kumar Mishra, Hafsa Jamshaid

Förderung

  • Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague grants no. 2022:31140/1312/3105: "Research on composite materials wit…
  • Internal grant agency of Faculty of Engineering, Czech University of Life Sciences Prague grants no. 2023:31140/1312/3104: "Development and testing of polymer…
  • Internal Grant Agency of the Faculty of Engineering, Czech University of Life Sciences Prague

Zitieren

APA

Jirků, P., Urban, J., Müller, M., Kolář, V., Chandan, V., Svobodová, J., Mishra, R. K., & Jamshaid, H. (2023). Evaluation of Mechanical Properties and Filler Interaction in the Field of SLA Polymeric Additive Manufacturing. Materials, 16(14), 4955. https://doi.org/10.3390/ma16144955

Vancouver

Jirků P, Urban J, Müller M, Kolář V, Chandan V, Svobodová J, et al. Evaluation of Mechanical Properties and Filler Interaction in the Field of SLA Polymeric Additive Manufacturing. Materials. 2023;16(14):4955. doi:10.3390/ma16144955

BibTeX
@article{Jirk2023,
  author = {Jirků, Petr and Urban, Jiří and Müller, Miroslav and Kolář, Viktor and Chandan, Vijay and Svobodová, Jaroslava and Mishra, Rajesh Kumar and Jamshaid, Hafsa},
  title = {Evaluation of Mechanical Properties and Filler Interaction in the Field of SLA Polymeric Additive Manufacturing},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {14},
  pages = {4955},
  doi = {10.3390/ma16144955}
}
Kostenlos starten →