EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Thermophysical Properties of Laser Powder Bed Fused Ti-6Al-4V and AlSi10Mg Alloys Made with Varying Laser Parameters

Stephen Akwaboa, Congyuan Zeng iD, Nigel Amoafo-Yeboah iD, Samuel Ibekwe, Patrick Mensah

Materials · 10.07.2023 · 16 (14) · 4920

DOI: 10.3390/ma16144920 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 10.07.2023. Verfasst von Stephen Akwaboa und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Southern University and A&M College, Baton Rouge, LA 70807, USA. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science Foundation, Louisiana NASA EPSCoR (LaSPACE), US National Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the influence of diverse laser processing parameters on the thermophysical properties of Ti-6Al-4V and AlSi10Mg alloys manufactured via laser powder bed fusion. During fabrication, the laser power (50 W, 75 W, 100 W) and laser scanning speed (0.2 m/s, 0.4 m/s, 0.6 m/s) were adjusted while keeping other processing parameters constant. Besides laser processing parameters, this study also explored the impact of test temperatures on the thermophysical properties of the alloys. It was found that the thermophysical properties of L-PBF Ti-6Al-4V alloy samples were sensitive to laser processing parameters, while L-PBF AlSi10Mg alloy showed less sensitivity. In general, for the L-PBF Ti-6Al-4V alloy, as the laser power increased and laser scan speed decreased, both thermal diffusivity and conductivity increased. Both L-PBF Ti-6Al-4V and L-PBF AlSi10Mg alloys demonstrated similar dependence on test temperatures, with thermal diffusivity and conductivity increasing as the test temperature rose. The CALPHAD software Thermo-Calc (2023b), applied in Scheil Solidification Mode, was utilized to calculate the quantity of solution atoms, thus enhancing our understanding of observed thermal conductivity variations. A detailed analysis revealed how variations in laser processing parameters and test temperatures significantly influence the alloy’s resulting density, specific heat, thermal diffusivity, and thermal conductivity. This research not only highlights the importance of processing parameters but also enriches comprehension of the mechanisms influencing these effects in the domain of laser powder bed fusion.

Schlagwörter

Stichwörter der Autor:innen

densitylaser powder bed fusionspecific heatthermal conductivitythermal diffusivity

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Southern University and A&M College, Baton Rouge, LA 70807, USA.
  • Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, NC 27695, USA.

ORCID-Profile: Congyuan Zeng, Nigel Amoafo-Yeboah

Förderung

  • National Science Foundation
  • Louisiana NASA EPSCoR (LaSPACE)
  • US National Science Foundation
  • Louisiana Board of Regents for the Louisiana Materials Design Alliance (LAMDA)
  • Louisiana NASA EPSCoR Faculty Fellow Program (FFP) + Summer Undergraduate Research Funding (SURF)

Zitieren

APA

Akwaboa, S., Zeng, C., Amoafo-Yeboah, N., Ibekwe, S., & Mensah, P. (2023). Thermophysical Properties of Laser Powder Bed Fused Ti-6Al-4V and AlSi10Mg Alloys Made with Varying Laser Parameters. Materials, 16(14), 4920. https://doi.org/10.3390/ma16144920

Vancouver

Akwaboa S, Zeng C, Amoafo-Yeboah N, Ibekwe S, Mensah P. Thermophysical Properties of Laser Powder Bed Fused Ti-6Al-4V and AlSi10Mg Alloys Made with Varying Laser Parameters. Materials. 2023;16(14):4920. doi:10.3390/ma16144920

BibTeX
@article{Akwaboa2023,
  author = {Akwaboa, Stephen and Zeng, Congyuan and Amoafo-Yeboah, Nigel and Ibekwe, Samuel and Mensah, Patrick},
  title = {Thermophysical Properties of Laser Powder Bed Fused Ti-6Al-4V and AlSi10Mg Alloys Made with Varying Laser Parameters},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {14},
  pages = {4920},
  doi = {10.3390/ma16144920}
}
Kostenlos starten →