Preheating Influence on the Precipitation Microstructure, Mechanical and Corrosive Properties of Additively Built Al–Cu–Li Alloy Contrasted with Conventional (T83) Alloy
Materials · 10.07.2023 · 16 (14) · 4916
DOI: 10.3390/ma16144916 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 10.07.2023. Verfasst von Frank Adjei-Kyeremeh und 7 weiteren Autor:innen. Beteiligte Einrichtung: Foundry Institute, RWTH Aachen University, Intzestraße 5, 52072 Aachen, Germany. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
In this paper, the high strength and lightweight Al–Cu–Li alloy (AA2099) is considered in as-built and preheated conditions (440 °C, 460 °C, 480 °C, 500 °C, and 520 °C). The purpose of this study is to investigate the influence of laser powder bed fusion (LPBF) in situ preheating on precipitation microstructure, mechanical and corrosive properties of LPBF-printed AA2099 alloy compared to the conventionally processed and heat-treated (T83) alloy. It is shown that precipitations evolve with increasing preheating temperatures from predominantly globular Cu-rich phases at lower temperatures (as-built, 440 °C) to more plate and rod-like precipitates (460 °C, 480 °C, 500 °C and 520 °C). Attendant increase with increasing preheating temperatures are the amount of low melting Cu-rich phases and precipitation-free zones (PFZ). Hardness of preheated LPBF samples peaks at 480 °C (93.6 HV0.1), and declines afterwards, although inferior to the T83 alloy (168.6 HV0.1). Preheated sample (500 °C) shows superior elongation (14.1%) compared to the T83 (11.3%) but falls short in tensile and yield strength properties. Potentiodynamic polarization results also show that increasing preheating temperature increases the corrosion current density (Icorr) and corrosion rate. Indicated by the lower oxide resistance (Rox), the Cu-rich phases compromise the integrity of the oxide layer.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Foundry Institute, RWTH Aachen University, Intzestraße 5, 52072 Aachen, Germany.
- Chair of Corrosion and Corrosion Protection, Foundry Institute, RWTH Aachen University, Intzestraße 5, 52072 Aachen, Germany.
- Steel Institute, RWTH Aachen University, Intzestraße 1, 52072 Aachen, Germany.
- Institute of Materials Engineering (IfW), University of Kassel, Moencheberg Str. 3, 34125 Kassel, Germany.
ORCID-Profile: Frank Adjei-Kyeremeh, Yudha Pratesa, Iris Raffeis, Daniela Zander
Zitieren
APA
Adjei-Kyeremeh, F., Pratesa, Y., Shen, X., Song, W., Raffeis, I., Vroomen, U., Zander, D., & Bührig-Polaczek, A. (2023). Preheating Influence on the Precipitation Microstructure, Mechanical and Corrosive Properties of Additively Built Al–Cu–Li Alloy Contrasted with Conventional (T83) Alloy. Materials, 16(14), 4916. https://doi.org/10.3390/ma16144916
Vancouver
Adjei-Kyeremeh F, Pratesa Y, Shen X, Song W, Raffeis I, Vroomen U, et al. Preheating Influence on the Precipitation Microstructure, Mechanical and Corrosive Properties of Additively Built Al–Cu–Li Alloy Contrasted with Conventional (T83) Alloy. Materials. 2023;16(14):4916. doi:10.3390/ma16144916
BibTeX
@article{AdjeiKyeremeh2023,
author = {Adjei-Kyeremeh, Frank and Pratesa, Yudha and Shen, Xiao and Song, Wenwen and Raffeis, Iris and Vroomen, Uwe and Zander, Daniela and Bührig-Polaczek, Andreas},
title = {Preheating Influence on the Precipitation Microstructure, Mechanical and Corrosive Properties of Additively Built Al–Cu–Li Alloy Contrasted with Conventional (T83) Alloy},
journal = {Materials},
year = {2023},
volume = {16},
number = {14},
pages = {4916},
doi = {10.3390/ma16144916}
}
EUVIMED