EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Analysis and Minimization of Race Tracking in the Resin-Transfer-Molding Process by Monte Carlo Simulation

Romain Agogué, Modesar Shakoor iD, Pierre Beauchêne, Chung Hae Park iD

Materials · 16.06.2023 · 16 (12) · 4438

DOI: 10.3390/ma16124438 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 16.06.2023. Verfasst von Romain Agogué und 3 weiteren Autor:innen. Beteiligte Einrichtung: IPC-Centre Technique Industriel de la Plasturgie et des Composites, Rue Léonard de Vinci, F-53810 Laval, France. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A numerical analysis of the influence of race tracking on dry spots formation and the accuracy of permeability measurement during the resin-transfer-molding process is presented. In the numerical simulation of the mold-filling process, defects are randomly generated, and their effect is assessed by a Monte Carlo simulation method. The effect of race tracking on the unsaturated permeability measurement and dry spots formation is investigated on flat plates. It is observed that the race-tracking defects located near the injection gate increase up to 40% of the value of the measured unsaturated permeability. The race-tracking defects located near the air vents are more likely to generate dry spots, whereas those near the injection gates have a less significant influence on dry spots generation. Depending on vent location, it has for instance been shown that the dry spot area can increase by a factor of 30. Dry spots may be mitigated by placing an air vent at a suitable location based on the numerical analysis results. Moreover, those results may be helpful to determine optimal sensor locations for the on-line control of mold-filling processes. Finally, the approach is successfully applied to a complex geometry.

Schlagwörter

Stichwörter der Autor:innen

Monte Carlo simulationdry spotspermeabilityrace trackingresin transfer molding (RTM)

Autor:innen und Institutionen

  • IPC-Centre Technique Industriel de la Plasturgie et des Composites, Rue Léonard de Vinci, F-53810 Laval, France.
  • IMT Nord Europe, Institut Mines-Télécom, Univ. Lille, Centre for Materials and Processes, F-59000 Lille, France.
  • ONERA (The French Aerospace Lab), 29 Avenue de la Division Leclerc, F-92320 Chatillon, France.

ORCID-Profile: Modesar Shakoor, Chung Hae Park

Zitieren

APA

Agogué, R., Shakoor, M., Beauchêne, P., & Park, C. H. (2023). Analysis and Minimization of Race Tracking in the Resin-Transfer-Molding Process by Monte Carlo Simulation. Materials, 16(12), 4438. https://doi.org/10.3390/ma16124438

Vancouver

Agogué R, Shakoor M, Beauchêne P, Park CH. Analysis and Minimization of Race Tracking in the Resin-Transfer-Molding Process by Monte Carlo Simulation. Materials. 2023;16(12):4438. doi:10.3390/ma16124438

BibTeX
@article{Agogu2023,
  author = {Agogué, Romain and Shakoor, Modesar and Beauchêne, Pierre and Park, Chung Hae},
  title = {Analysis and Minimization of Race Tracking in the Resin-Transfer-Molding Process by Monte Carlo Simulation},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {12},
  pages = {4438},
  doi = {10.3390/ma16124438}
}
Kostenlos starten →