EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Cutting-Edge Microgeometry on Cutting Forces in High-Speed Milling of 7075 Aluminum Alloy

Łukasz Żyłka iD, Rafał Flejszar iD, Paweł Lajmert

Materials · 20.05.2023 · 16 (10) · 3859

DOI: 10.3390/ma16103859 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 20.05.2023. Verfasst von Łukasz Żyłka und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Manufacturing Techniques and Automation, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, W. Po…. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: PODKARPACKIE CENTRUM INNOWACJI, European Regional Development Fund.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In the present study, the impact of cutting-edge microgeometry on the cutting forces in the finish milling of a 7075-aluminium alloy was analysed. The influence of selected values of the rounding radius of cutting edge, and the size of the margin width, on the cutting-force parameters was analysed. Experimental tests were carried out for different cross-sectional values of the cutting layer, changing the feed per tooth and radial infeed parameters. An analysis of the various statistical parameters of the force signal was performed. Experimental mathematical models of the relationship of the force parameters to the radius of the rounded cutting edge and the width of the margin were developed. The cutting forces were found to be most strongly influenced by the width of the margin and, to a minor extent, by the rounding radius of the cutting edge. It was proved that the effect of margin width is linear, and the effect of radius R is nonlinear and nonmonotonic. The minimum cutting force was shown to be for the radius of rounded cutting edge of about 15–20 micrometres. The proposed model is the basis for further work on innovative cutter geometries for aluminium-finishing milling.

Schlagwörter

Stichwörter der Autor:innen

cutting forcescutting-edge microgeometrymilling

Autor:innen und Institutionen

  • Department of Manufacturing Techniques and Automation, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, W. Pola 2 Str, 35-959 Rzeszow, Poland.
  • Faculty of Mechanical Engineering, Lodz University of Technology, Stefanowskiego 1/15 Str, 90-537 Lodz, Poland.

ORCID-Profile: Łukasz Żyłka, Rafał Flejszar

Förderung

  • PODKARPACKIE CENTRUM INNOWACJI
  • European Regional Development Fund

Zitieren

APA

Żyłka, Ł., Flejszar, R., & Lajmert, P. (2023). Influence of Cutting-Edge Microgeometry on Cutting Forces in High-Speed Milling of 7075 Aluminum Alloy. Materials, 16(10), 3859. https://doi.org/10.3390/ma16103859

Vancouver

Żyłka Ł, Flejszar R, Lajmert P. Influence of Cutting-Edge Microgeometry on Cutting Forces in High-Speed Milling of 7075 Aluminum Alloy. Materials. 2023;16(10):3859. doi:10.3390/ma16103859

BibTeX
@article{yka2023,
  author = {Żyłka, Łukasz and Flejszar, Rafał and Lajmert, Paweł},
  title = {Influence of Cutting-Edge Microgeometry on Cutting Forces in High-Speed Milling of 7075 Aluminum Alloy},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {10},
  pages = {3859},
  doi = {10.3390/ma16103859}
}
Kostenlos starten →