EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

From Electronic Waste to 3D-Printed Product, How Multiple Recycling Affects High-Impact Polystyrene (HIPS) Filament Performances

Edbert Wing Hanitio, Novan Rifky Lutfhyansyah iD, Balqis Mentari Efendi, Yati Mardiyati iD, Steven Steven iD

Materials · 27.04.2023 · 16 (9) · 3412

DOI: 10.3390/ma16093412 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.04.2023. Verfasst von Edbert Wing Hanitio und 4 weiteren Autor:innen. Beteiligte Einrichtung: Materials Science and Engineering Research Group, Faculty of Mechanical and Aerospace Engineering, Institut Teknologi Bandung, Jl. Ganesha No. 10, Ba…. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Research and Community Service Program (P2MI), Faculty of Mechanical and Aerospace Engineering ITB 2021.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The rapid growth of the electronics industry is producing excessive electronic waste. One of the common types of materials in electronic waste is high-impact polystyrene (HIPS). In this study, HIPS from electronic waste was recycled through an extrusion process and used as a 3D print filament. The effects of recycling on printability, physical properties, and mechanical properties in horizontal and vertical directions were examined. It was found that until the fourth-cycle, mechanical properties such as horizontal tensile strength, horizontal flexural strength, vertical flexural strength, and vertical impact strength were comparable with virgin commercial filament. In addition, the vertical flexural modulus in the fourth cycle increased by 77.28%. However, the density of recycled HIPs’ first to the fourth cycle slightly decreased by 10.6%, and the melt flow rate increased by 20.3%. It was also observed that until the third cycle, the effect of the reprocessing steps was insignificant on the defect of the 3D-printed product. In general, the experiments show various results, mainly in mechanical properties. Nevertheless, recycled HIPS filaments are comparable to or better than commercial ones in some cases. As a result, recycled HIPS filaments hold the potential to be considered as an alternative to other types of 3D print filaments.

Schlagwörter

Stichwörter der Autor:innen

3D printingelectronic wastehigh-impact polystyrenemechanical propertiesrecycling

Autor:innen und Institutionen

  • Materials Science and Engineering Research Group, Faculty of Mechanical and Aerospace Engineering, Institut Teknologi Bandung, Jl. Ganesha No. 10, Bandung 40132, Indonesia.

ORCID-Profile: Novan Rifky Lutfhyansyah, Yati Mardiyati, Steven Steven

Förderung

  • Research and Community Service Program (P2MI), Faculty of Mechanical and Aerospace Engineering ITB 2021

Zitieren

APA

Hanitio, E. W., Lutfhyansyah, N. R., Efendi, B. M., Mardiyati, Y., & Steven, S. (2023). From Electronic Waste to 3D-Printed Product, How Multiple Recycling Affects High-Impact Polystyrene (HIPS) Filament Performances. Materials, 16(9), 3412. https://doi.org/10.3390/ma16093412

Vancouver

Hanitio EW, Lutfhyansyah NR, Efendi BM, Mardiyati Y, Steven S. From Electronic Waste to 3D-Printed Product, How Multiple Recycling Affects High-Impact Polystyrene (HIPS) Filament Performances. Materials. 2023;16(9):3412. doi:10.3390/ma16093412

BibTeX
@article{Hanitio2023,
  author = {Hanitio, Edbert Wing and Lutfhyansyah, Novan Rifky and Efendi, Balqis Mentari and Mardiyati, Yati and Steven, Steven},
  title = {From Electronic Waste to 3D-Printed Product, How Multiple Recycling Affects High-Impact Polystyrene (HIPS) Filament Performances},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {9},
  pages = {3412},
  doi = {10.3390/ma16093412}
}
Kostenlos starten →