EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Analysis of Mechanical Properties and Geometric Accuracy in Specimens Printed in Material Jetting Technology

Natalia Majca-Nowak iD, Paweł Pyrzanowski iD

Materials · 11.04.2023 · 16 (8) · 3014

DOI: 10.3390/ma16083014 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 11.04.2023. Verfasst von Natalia Majca-Nowak und 1 weiteren Autor:innen. Beteiligte Einrichtung: Łukasiewicz Research Network-Institute of Aviation, al. Krakowska 110/114, 02-256 Warsaw, Poland. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Łukasiewicz Research Network—Institute of Aviation in Warsaw.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The purpose of this research was to analyze polymer materials based on mechanical properties and geometrical parameters, such as the smallest material deviations and the best printing texture after three-dimensional (3D) printing in two methods of Material Jetting technology: PolyJet and MultiJet. This study covers checks for Vero Plus, Rigur, Durus, ABS, and VisiJet M2R-WT materials. Thirty flat specimens were printed both for 0 and 90 raster orientations. Specimen scans were superimposed on the 3D model from CAD software. Each of them was tested, paying attention to the accuracy and the layer thickness effect of printed components. Then, all specimens were subjected to tensile tests. The obtained data—Young’s modulus and Poisson’s ratio—were compared using statistical methods, focusing on the two most important parameters: the isotropy of the printed material in two directions and the characteristics close to linear. It was found that unitary surface deviation with general dimensional accuracy equal to ±0.1 mm was the common feature of printed models. Some small areas had lower accuracy depending on the material and printer device. Rigur material obtained the highest mechanical properties. Dimensional accuracy in Material Jetting technology as a function of layer parameters such as layer thickness and raster orientation was checked. The materials were checked in terms of relative isotropy and linearity. Additionally, similarities and differences between PolyJet and MultiJet methods were covered.

Schlagwörter

Stichwörter der Autor:innen

DurusMaterial JettingMultiJetPolyJetRigurVeroVisiJetacrylonitrile butadiene styrene (ABS)additive manufacturinglayer heightlayer orientationtensile behavior

Autor:innen und Institutionen

  • Łukasiewicz Research Network-Institute of Aviation, al. Krakowska 110/114, 02-256 Warsaw, Poland.
  • Institute of Aeronautics and Applied Mechanics, Warsaw University of Technology, Nowowiejska Str. 24, 00-665 Warsaw, Poland.

ORCID-Profile: Natalia Majca-Nowak, Paweł Pyrzanowski

Förderung

  • Łukasiewicz Research Network—Institute of Aviation in Warsaw

Zitieren

APA

Majca-Nowak, N., & Pyrzanowski, P. (2023). The Analysis of Mechanical Properties and Geometric Accuracy in Specimens Printed in Material Jetting Technology. Materials, 16(8), 3014. https://doi.org/10.3390/ma16083014

Vancouver

Majca-Nowak N, Pyrzanowski P. The Analysis of Mechanical Properties and Geometric Accuracy in Specimens Printed in Material Jetting Technology. Materials. 2023;16(8):3014. doi:10.3390/ma16083014

BibTeX
@article{MajcaNowak2023,
  author = {Majca-Nowak, Natalia and Pyrzanowski, Paweł},
  title = {The Analysis of Mechanical Properties and Geometric Accuracy in Specimens Printed in Material Jetting Technology},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {8},
  pages = {3014},
  doi = {10.3390/ma16083014}
}
Kostenlos starten →